← Back to BMW 3-Series Guides

2020–2024 BMW 3-Series

2020-2024 BMW 3 Series — Replace Engine Fuse

By Tom Becker ✓ Certified Mechanic · Published Sep 21, 2026 · Updated Oct 22, 2026

🔧🔧 Moderate 30 minutes $2 DIY 3 views

Save $118 by doing it yourself! Shop cost: $120

Quick answer: Replace Engine Fuse on a 2020–2024 BMW 3-Series is rated Moderate and takes about 30 minutes. You'll need 4 tools for this job, and parts cost about $2. This guide walks you through the full job step by step, including the mistakes to avoid.

Quick Video Tutorial

Parts You Need

Total Cost
$2.00
Part Name Part Number Price Buy
20 Amp Fuse 61136942071 $2.00
30 Amp Fuse Optional 61139230533 $3.00
40 Amp Fuse Optional 61139826751 $4.00

About prices: shown prices are typical retail averages and change frequently; cheaper alternatives may be available. Confirm the current price before buying.

💡 Pro tip: Order all parts at once to save on shipping

Step-by-Step Instructions

Follow these steps carefully

1

Identify the failed circuit and correct fuse rating

First, identify exactly which circuit is dead on the 2020-2024 BMW 3 Series 320i (G20 chassis; the procedure below matches the 2020-2024 car).

2

Access the engine fuse box safely

The G20 3 Series has four fuse boxes, and engine-related fuses live in the front ones: one at the front left and one at the front right of the cabin (near the A-pillars, behind trim panels), plus the BDC (body domain controller) box, with a fourth main box in the trunk behind the right-side wheel-arch panel. Open the hood and locate the engine-bay power distribution box as well. With dry hands, release the cover clips on the relevant box. There is usually a fuse puller clipped inside the box lid — use it instead of pliers, which crack the fuse bodies. Recommended: disconnect the negative battery cable if you will probe terminals or replace high-amperage cartridge fuses.

🔧 Mechanic's note — Tom Becker

I use the fuse puller clipped inside the lid — I've cracked fuse bodies with pliers before, and the puller is right there for a reason.

3

Verify the suspect fuse with a multimeter

But a fuse that looks perfect can still be open, so verify with a multimeter on continuity mode or a 12V test light — this takes ten seconds and eliminates guessing.

🔧 Mechanic's note — Ray Delgado

I test with a multimeter even when the fuse looks perfect — I've been burned by a fuse that looked fine but was open, and the ten-second test is free.

4

Install the correct replacement fuse

Install a new fuse of the identical amperage and the identical physical type — the G20 uses mini, standard ATO, and larger maxi/cartridge fuses, and they are not interchangeable. Do not force a fuse into the wrong cavity — if it does not fit easily, you have the wrong type.

5

Reassemble and reconnect power

Refit the fuse-box cover so it clicks fully shut — the cover is also a weather seal, and a poorly seated cover lets moisture corrode the whole box. Reconnect the battery if you disconnected it.

🔧 Mechanic's note — Tom Becker

I make sure the cover clicks fully shut — it's also the weather seal, and I've seen a poorly seated cover let moisture corrode the whole box.

6

Test the circuit and investigate repeat blows

Switch on the related circuit and confirm full operation on the 2020-2024 BMW 3 Series 320i. If the new fuse blows immediately, stop — a repeat blow means a short, and each new fuse re-energizes the fault. If the fuse holds, run the circuit through several on/off cycles before calling it fixed.

All Done!

Test your repair before closing everything up. If something doesn't work right, double-check your steps.

⚠️ Common Mistakes to Avoid

  • • Using a fuse with incorrect amperage rating
  • • Not securely reassembling the fuse box cover
  • • Failing to disconnect the battery before starting the repair