← Back to BMW M2 Guides

2016–2024 BMW M2

2016-2024 BMW M2 — Cabin Air Filter Replacement

By Tom Becker ✓ Certified Mechanic · Published Sep 21, 2026 · Updated Oct 22, 2026

🔧 Easy 15–25 minutes depending on generation $28 DIY

Save $72 by doing it yourself! Shop cost: $100

Quick answer: Cabin Air Filter Replacement on a 2016–2024 BMW M2 is rated Easy and takes about 15–25 minutes depending on generation. You'll need 2 tools for this job, and parts cost about $28. This guide walks you through the full job step by step, including the mistakes to avoid.

Quick Video Tutorial

Parts You Need

Total Cost
$28.00
Part Name Part Number Price Buy
Cabin air filter for 2016-2024 BMW M2; verify arrows, size, and VIN/trim fitment — $28.00

About prices: shown prices are typical retail averages and change frequently; cheaper alternatives may be available. Confirm the current price before buying.

💡 Pro tip: Order all parts at once to save on shipping

Step-by-Step Instructions

Follow these steps carefully

1

Identify which M2 generation you have

2016–2021 (F87): microfilter behind the glove box, accessed from the footwell after dropping a dash trim panel. 2023–2024 (G87): filter pair under the passenger-side footwell, thumb-screw trim panel and Torx-secured housing lid. Check your model year first.

🔧 Mechanic's note — Ray Delgado

In my experience, Get the generation wrong and you'll be tearing apart the wrong end of the dash. Check the badge and model year before you touch anything — the F87 and G87 jobs look nothing alike.

2

Clear the passenger footwell on either generation

Move the passenger seat fully rearward, lay a towel across the door sill, and put on a headlamp. Gather a T15/T20 Torx set and a trim tool; the G87 needs the Torx driver for the housing lid.

3

F87 (2016–2021): drop the lower dash trim

On the F87, pull the dash trim panel down with a trim tool — clips and usually one screw. Behind it is the filter-housing cover; release its clips or tabs and pull it off. Work gently: F87 plastics get brittle.

🔧 Mechanic's note — Ray Delgado

From my bay, Those F87 dash plastics are old enough to vote — treat every clip like it's going to snap, because it might. Feel for the release direction instead of forcing it.

4

G87 (2023–2024): remove the footwell panel and housing lid

On the G87, turn the two thumb screws 90 degrees and pull the front edge down to free the guide hooks. Disconnect the footwell-light wiring plug and unclip its retainer. Remove the Torx bolts (T15/T20) and pull the drain tube off.

5

Remove the old filter and record its orientation

Pull the filter(s) down and out. Cabin filters are airflow-specific and the G87's pair can sit mirrored — photograph them in the housing first. G87: press the recirculation button (ignition in accessory, engine off) before installing to park the fresh-air flap closed.

🔧 Mechanic's note — Ray Delgado

Take it from me: G87 owners, that recirculation trick is BMW's own fix — don't skip it. An over-driven fresh-air flap turns a 20-minute job into a do-over with the whole housing open again.

6

Install the new filter in the original orientation

Slide the filter up into place, matching your photo's orientation. Never force a filter that won't seat. F87: refit the housing cover and dash trim. G87: refit the drain tube and lid, snug the Torx bolts — stop at snug.

7

Reassemble the footwell and test the HVAC

Reconnect the footwell-light plug and refit the trim panel — F87 clips, G87 guide hooks and thumb screws. Test fresh-air fan low to max, then recirculation: strong airflow. Footwell whistling means a mis-seated filter or loose cover.

All Done!

Test your repair before closing everything up. If something doesn't work right, double-check your steps.

⚠️ Common Mistakes to Avoid

  • • Following the wrong generation’s procedure — F87 and G87 housings are in different spots
  • • Installing the G87’s filter pair in mirrored-wrong orientations
  • • Forcing brittle F87 dash clips instead of feeling for the release direction
  • • Over-tightening the G87’s plastic housing-lid bolts and stripping the threads