← Back to BMW M5 Guides

2013–2018 BMW M5

2013-2018 BMW M5 — Oil and Filter Change

By Tom Becker ✓ Certified Mechanic · Published Sep 24, 2026 · Updated Nov 7, 2026

🔧🔧 Moderate 60–90 minutes $85 DIY

Save $89 by doing it yourself! Shop cost: $174

Quick answer: Oil and Filter Change on a 2013–2018 BMW M5 is rated Moderate and takes about 60–90 minutes. You'll need 7 tools for this job, and parts cost about $85. This guide walks you through the full job step by step, including the mistakes to avoid.

Quick Video Tutorial

Parts You Need

Total Cost
$85.00
Oil spec 4.4L S63 V8
Capacity 8.9 qt with filter Viscosity 0W-40 (alt: 0W-30, 5W-30) Spec BMW Longlife-01 / Longlife-01 FE
Part Name Part Number Price Buy
S63 oil filter cartridge element (with O-rings) — $32.00
Oil drain plug crush washer — $1.00
BMW LL-01 approved 0W-40 engine oil, approx 8.5 liters (8.9 qt) — $52.00

About prices: shown prices are typical retail averages and change frequently; cheaper alternatives may be available. Confirm the current price before buying.

💡 Pro tip: Order all parts at once to save on shipping

Step-by-Step Instructions

Follow these steps carefully

1

Warm up and secure the car

Start the engine and idle it for two to three minutes so the oil warms and drains quickly, then shut it off. Park on level ground, set the parking brake, and chock the rear wheels.

2

Lift the car and remove the splash shield

Lift the front onto jack stands at the reinforced jack pads and remove the underbody splash shield (a mix of 8mm screws and plastic fasteners) to expose the oil pan.

3

Drain the engine oil

Place a large drain pan under the sump and remove the oil drain plug, letting the oil flow out for 10 to 15 minutes. Fit a new aluminum crush washer on the plug when you reinstall it — the old one will not seal twice.

4

Remove the oil filter cartridge

From the top of the engine bay, locate the black plastic oil filter housing and unscrew its cap with a 36mm socket. Lift out the spent cartridge filter and remove the old O-rings from the cap.

5

Fit the new filter and seals

Lubricate the new O-rings with fresh oil, seat them in the cap grooves, and drop in the new filter cartridge. Thread the cap on by hand, then snug it with the 36mm socket without overtightening the plastic.

🔧 Mechanic's note — Ray Delgado

I learned this one the hard way — I thread the cap on by hand, then snug it with the 36mm socket without overtightening the plastic.

6

Reinstall the drain plug and shield

Thread the drain plug in by hand first so you do not cross-thread the aluminum pan, then tighten it firmly with the new crush washer. Reinstall the splash shield with all of its original screws and fasteners.

🔧 Mechanic's note — Ray Delgado

My shop habit: Thread the drain plug in by hand first so you do not cross-thread the aluminum pan, then tighten it firmly with the new crush washer.

7

Refill with fresh oil

Add approximately 8.5 liters (8.9 quarts) of BMW LL-01 approved 0W-40 through the oil filler, pouring the final portion slowly. The S63 has no dipstick, so add carefully and verify electronically rather than guessing.

🔧 Mechanic's note — Tom Becker

This is the part I see people get wrong: the S63 has no dipstick, so I add carefully and verify electronically rather than guessing.

8

Verify the level and reset the reminder

Start the engine, check underneath for leaks at the plug and filter housing, then read the electronic oil level in iDrive after a few minutes of idling. Top up as needed and reset the oil service reminder in the Condition Based Service menu.

All Done!

Test your repair before closing everything up. If something doesn't work right, double-check your steps.

⚠️ Common Mistakes to Avoid

  • • Using oil that is not BMW LL-01 approved, which the S63 twin-turbo V8 is picky about.
  • • Forgetting the new crush washer on the drain plug and getting a slow leak.
  • • Overtightening the plastic filter housing cap until it cracks.
  • • Skipping the iDrive electronic oil level check — there is no dipstick to double-check with.
  • • Not resetting the Condition Based Service oil reminder, so the dash keeps nagging for a change.