Quick answer: Spark Plug Replacement on a 2012–2016 Cadillac SRX is rated Advanced and takes about 2-3 hours. You'll need 10 tools for this job, and parts cost about $304. This guide walks you through the full job step by step, including the mistakes to avoid.
| Part Name |
Part Number |
Price |
Buy |
| ACDelco 41-109 Spark Plugs |
41-109 |
$77.95 |
|
| ACDelco Ignition Coils |
D515C |
$225.95 |
|
| New intake gasket |
— |
— |
|
About prices: shown prices are typical retail averages and change frequently; cheaper alternatives may be available. Confirm the current price before buying.
💡 Pro tip: Order all parts at once to save on shipping
Step-by-Step Instructions
Follow these steps carefully
1
Cool the engine (verify 2012+ LFX!)
The 2012–2016 Cadillac SRX 3.6L (LFX V6) uses ACDelco 41-109 plugs. Gap: 0.043" (pre-gapped). Torque: not verified — check the service manual (do not guess). You'll need: 6x ACDelco 41-109, spark plug socket, extensions, intake gasket set. Verify you have the 3.6L LFX (2012+).
🔧 Mechanic's note — Ray Delgado
I confirm the LFX and let the SRX cool — then the torque wrench comes out for the plugs. The 3.6L head is aluminum, and I treat every plug like the threads are made of glass, because they nearly are.
2
Access coils (rear bank needs intake off)
Remove the engine cover. The REAR bank (firewall side) is under the upper intake manifold — you MUST remove the intake to reach the rear plugs. Disconnect the intake tubing, unbolt the upper intake, label sensors/vacuum lines, lift it off. Take photos.
3
Remove one coil at a time
Start with the easy front bank. Unplug the connector, unbolt the coil, pull it out. Keep track. The LFX's coils are reliable — inspect the boots. Don't drop anything into the open intake ports — cover them with rags.
4
Remove the old spark plug
Remove the old ACDelco 41-109 with your socket. The old plugs should show normal LFX wear. If a plug is oil-fouled, check the valve covers. For the rear bank, use long extensions working against the firewall. Don't drop debris into the cylinders or intake ports.
5
Gap and hand-thread the new plug
The new ACDelco 41-109 comes pre-gapped at 0.043" — verify but don't adjust (iridium). Hand-thread the new plug into the LFX's head until it seats. NEVER wrench-start — the aluminum heads strip. For the rear bank, hand-thread working blind — use fuel hose on the plug to feel it. If it binds, back out. Ensure it's the 41-109 (not the LY7's 41-990 or the LGX's 41-130).
🔧 Mechanic's note — Tom Becker
In my experience, plastic and aluminum don't forgive overtightening the way steel does. Snug plus a quarter turn, then stop and walk away.
6
Torque to specification (verify!)
Torque to Cadillac spec — not verified for the LFX, so check your service manual. Do NOT guess. The LFX's aluminum heads need precise torque. Use a torque wrench. The 0.043" pre-gap and correct torque are critical for the DI engine.
7
Reinstall coils and intake
Repeat for all 6, one at a time. Torque the intake bolts to spec. Remove the rags from the intake ports before installing! Double-check every connection — the LFX's DI system is sensitive to vacuum leaks. Refit each coil, bolt it, and reconnect its connector.
8
Reassemble and test
Reinstall the engine cover. Start the engine — the 3.6L LFX should idle smoothly. Check for misfire codes and vacuum leaks. The SRX's rear-bank intake job means many connections — a rough idle is usually a missed line or the intake gasket. Test drive: the LFX should pull strongly. The ACDelco 41-109 at 0.043" is the correct plug. Remember: this is the 2012–2016 LFX — if you have a 2010–2011 3.0L, the plugs and procedure differ. The LFX's direct injection means the plugs work harder — use OE ACDelco.
🔧 Mechanic's note — Ray Delgado
I drive the SRX after a plug change and watch for a flashing check-engine light under load. The 3.6L hides a weak coil at idle, and I would rather find it now than on the customer's commute.
All Done!
Test your repair before closing everything up. If something doesn't work right, double-check your steps.
⚠️ Common Mistakes to Avoid
- • Not properly gapping the new spark plugs
- • Forgetting to torque the spark plugs to manufacturer specifications
- • Failing to replace ignition coils if they show signs of wear