← Back to Chevrolet Colorado ZR2 Guides

2017–2024 Chevrolet Colorado ZR2

2017-2024 Chevrolet Colorado ZR2 — Engine Air Filter Replacement

By Ray Delgado ✓ Certified Mechanic · Published Sep 21, 2026 · Updated Oct 22, 2026

🔧 Easy 20-45 minutes $35 DIY

Save $75 by doing it yourself! Shop cost: $110

Quick answer: Engine Air Filter Replacement on a 2017–2024 Chevrolet Colorado ZR2 is rated Easy and takes about 20-45 minutes. You'll need 2 tools for this job, and parts cost about $35. This guide walks you through the full job step by step, including the mistakes to avoid.

Quick Video Tutorial

Parts You Need

Total Cost
$35.00
Part Name Part Number Price Buy
Engine air filter for 2017-2024 Chevrolet Colorado ZR2; verify engine, housing shape, and VIN fitment — $35.00

About prices: shown prices are typical retail averages and change frequently; cheaper alternatives may be available. Confirm the current price before buying.

💡 Pro tip: Order all parts at once to save on shipping

Step-by-Step Instructions

Follow these steps carefully

1

Confirm filter fitment and engine state

Park on level ground, switch the engine off, and let the bay cool. Note that 2017+ Colorados have an Air Filter Life monitor in the Driver Information Center, so check its reading while you are under the hood.

2

Open the air box

First remove the two screws that secure the stock intake tube and slide the tube off, giving the airbox lid room to move. Then unlatch the two clips at the top of the airbox — they are the lid's only retainers, so do not pry anywhere else. Lift the airbox lid and upper base away from the lower half without pulling on the MAF sensor wiring on the intake tube; the MAF pad and sensor sit right on the tube, and the sensor element must stay clean and untouched. Cover the open intake with a clean towel.

🔧 Mechanic's note — Tom Becker

I never pry anywhere but those two clips — they're the lid's only retainers, and the MAF pad and sensor sit right on that intake tube. Keep the sensor element clean and untouched.

3

Inspect the old filter and housing

Lift the old panel filter out of the airbox base and note which face is dirty to set the airflow direction. Vacuum the base for sand and leaf debris — ZR2s see dusty trails, and this box ingests plenty of it. Inspect the lid seal for flattening, check the intake tube and its two screws' mounting points for cracks, and confirm the MAF sensor and its harness are undamaged. If you disturbed the tube, make sure the MAF pad will reseat in its correct orientation on reassembly.

4

Install the new filter

Place the new filter into the base of the airbox so the tabs on the filter rest inside the matching tabs in the box — when positioned correctly the panel sits flat with no rocking. Verify the filter edge fits tight to the housing all the way around; an edge gap on this truck feeds dust straight to the throttle body. Set the upper base and lid back down squarely on the seal before touching the clips, and never use the clips to pull a misaligned lid into place.

🔧 Mechanic's note — Ray Delgado

I never use the clips to pull a misaligned lid into place — seat the lid squarely on the seal first. An edge gap on this truck feeds dust straight to the throttle body.

5

Close and verify the intake

Relatch the two clips at the top of the airbox with even tension, then reinstall the stock intake tube and secure it with the two screws you removed. Remove the towel, confirm the MAF harness is connected, then start the engine and listen at the airbox for a hiss or whistle indicating an intake leak. Check for no check-engine light and no rough idle, and reset the Air Filter Life monitor in the Driver Information Center per your owner's manual before you close the hood.

All Done!

Test your repair before closing everything up. If something doesn't work right, double-check your steps.

⚠️ Common Mistakes to Avoid

  • • Confusing the engine filter with the cabin filter
  • • Installing the filter upside down or leaving a corner unseated
  • • Dropping clips, dirt, or shop towels into the intake tract
  • • Over-tightening plastic air-box fasteners
  • • Failing to reconnect the intake duct or sensor connector