← Back to Chevrolet Corvette Guides

2005–2013 Chevrolet Corvette

2005-2013 Chevrolet Corvette — Wiper Blade Replacement

By Ray Delgado ✓ Certified Mechanic · Published Sep 21, 2026 · Updated Oct 22, 2026

🔧 Easy 10–15 minutes $66 DIY

Quick answer: Wiper Blade Replacement on a 2005–2013 Chevrolet Corvette is rated Easy and takes about 10–15 minutes. Parts cost about $66. This guide walks you through the full job step by step, including the mistakes to avoid.

Quick Video Tutorial

Parts You Need

Total Cost
$65.98
Part Name Part Number Price Buy
Driver wiper blade, 21" Bosch 21A $32.99
Passenger wiper blade, 21" Bosch 21B $32.99

About prices: shown prices are typical retail averages and change frequently; cheaper alternatives may be available. Confirm the current price before buying.

💡 Pro tip: Order all parts at once to save on shipping

Step-by-Step Instructions

Follow these steps carefully

1

Buy two 21-inch blades with U-hook connectors

One detail from owners: the original driver's blade carries an attached aero spoiler to hold it down at speed, while the passenger blade does not, so when you buy your pair, note which replacement is intended for the driver's side if the set distinguishes them.

2

Open the hood, then stop the wipers mid-sweep

The C6's wipers park tucked beneath the hood's trailing edge, so the hood must be open before you touch them — otherwise you cannot lift the arms at all.

🔧 Mechanic's note — Ray Delgado

The blade refill option saves money if the frames are good. I check frames for rust before deciding. I clean the blade edge with a damp cloth. Sometimes 'worn' blades just have built-up grime.

3

Release the tab and slide the driver's blade off

Lift the driver's arm away from the glass until it holds upright, and lay your towel on the windshield beneath it. Find the release tab on the blade's hook connector, press it, and slide the blade downward off the hook.

4

Fit the new driver's blade, spoiler side correct

Thread the new 21-inch driver's blade onto the hook and slide it upward until the tab clicks into place. Check that the blade sits straight along the arm — and if your set includes the aero-spoiler blade, make sure that is the one on the driver's side, spoiler facing into the wind. Tug the blade firmly to confirm the latch, then lower the arm back onto the windshield slowly by hand.

5

Swap the passenger blade in its limited space

Now the fiddly one. Work with the arm close to the windshield: press the release tab, slide the old blade off the hook, and thread the new 21-inch blade on in the limited space.

6

Detail the windshield and cowl while the arms are up

With both arms still raised, clean the entire windshield with glass cleaner — on a low, raked windshield like the C6's, a film of road grime is surprisingly visible at night.

7

Test both speeds and watch for high-speed chatter

Lower both arms fully onto the glass, close the hood, and start the car. Run the washers and wipers through several cycles at low and high speed, watching for quiet, streak-free sweeps across the whole blade length.

All Done!

Test your repair before closing everything up. If something doesn't work right, double-check your steps.

⚠️ Common Mistakes to Avoid

  • • Forcing the passenger-side arm upward like the driver's side. The passenger arm barely pivots — about four inches off the glass is all you get — and forcing it bends the arm.
  • • Closing the hood while the wiper arms are still raised. The arms park beneath the hood's trailing edge, and the hood will strike them.
  • • Buying two identical blades without checking the aero spoiler: the original driver's blade carries an attached wind spoiler that the passenger blade lacks, so confirm which of your new blades is meant for the driver's side.