← Back to Chevrolet Cruze Guides

2011–2015 Chevrolet Cruze

2011-2015 Chevrolet Cruze - Thermostat Replacement

By Ray Delgado ✓ Certified Mechanic · Published Sep 21, 2026 · Updated Oct 22, 2026

🔧🔧 Moderate 2-3 hours $180 DIY 2 views

Save $520 by doing it yourself! Shop cost: $700

Quick answer: Thermostat Replacement on a 2011–2015 Chevrolet Cruze is rated Moderate and takes about 2-3 hours. You'll need 9 tools for this job, and parts cost about $180. This guide walks you through the full job step by step, including the mistakes to avoid.

Quick Video Tutorial

Parts You Need

Total Cost
$180.00
Part Name Part Number Price Buy
Thermostat Housing Assembly 55579010 $150.00
Coolant 12346290 $30.00

About prices: shown prices are typical retail averages and change frequently; cheaper alternatives may be available. Confirm the current price before buying.

💡 Pro tip: Order all parts at once to save on shipping

Step-by-Step Instructions

Follow these steps carefully

1

Prepare (housing assembly, 1.4T!)

The 2011–2015 Chevrolet Cruze (1.4L turbo LUJ/LUV — the most common) thermostat replacement: the thermostat is INTEGRATED into a plastic water outlet/housing assembly on the DRIVER'S side — serviced as a complete housing, NOT a separate thermostat. OE: GM 55579010 / 55565336 / 55593034 / 25200455; aftermarket Dorman 902-808. It's ELECTRONICALLY CONTROLLED (map stat) — the ECM drives a heater element via PWM. P0597/P0598 = heater circuit fault; P0128 = stuck open. Opening temp 105°C (221°F). You'll need: new housing assembly, Dex-Cool coolant (GM 12346290 concentrate or 50/50 premix), E10 socket, 7mm socket, T20, hose clamp pliers, torque wrench. Remove the air intake duct for access. Disconnect the ECT sensor connector on the housing (inspect for corrosion). DO NOT over-tighten the plastic housing — 8 N·m (71 lb-in) max (service-table value — verify). Cracking the housing is the #1 comeback. Note: this guide is the 1.4L turbo; the 1.8L NA is similar but verify part numbers.

🔧 Mechanic's note — Tom Becker

I stop shopping for a standalone thermostat — on the 1.4T it doesn't exist as a separate part. The whole plastic housing is the service part, and the 8 N·m torque limit is real: crack it overtightening and you're buying the housing twice.

2

Access the Driver's-Side Housing

Drain the coolant via the surge tank. Remove the air intake duct. Note the 4 hoses attached: radiator inlet, oil cooler inlet, heater inlet, and the air bleed hose. Disconnect the ECT sensor electrical connector on the housing — check the pins for corrosion.

3

Remove the Housing Assembly

Remove the E10 housing bolts. Remove the housing with the integrated thermostat. The old unit is electronic — disconnect its heater element wiring. The unit is designed to fail OPEN (P0128, low gauge, weak heat = stuck open).

4

Install New Housing (8 N·m max!)

Install the new housing assembly (55579010 or equivalent). Torque the E10 bolts to 8 N·m (71 lb-in) — service-table value; the housing is PLASTIC and cracks if over-tightened. Reconnect the ECT sensor connector and the thermostat heater wiring. Reconnect all 4 hoses (radiator inlet, oil cooler inlet, heater inlet, air bleed). Reinstall the air intake duct. The 8 N·m is a light torque — use a torque wrench, not a breaker bar.

🔧 Mechanic's note — Ray Delgado

Eight newton-meters is wrist torque, not arm torque — use the small torque wrench, not the big one. I've seen more of these housings cracked by a 3/8-drive ratchet than by heat cycling.

5

Refill Dex-Cool, Bleed Carefully

Refill with Dex-Cool (orange OAT) through the SURGE TANK — not the radiator (no cap). Use 50/50 Dex-Cool/distilled or concentrate 12346290 + distilled. Do NOT mix with green or Asian coolants. Fill to the surge tank seam/MAX line. The 1.4T's self-bleeding design uses the air bleed hose — but air pockets are the #1 comeback cause. Practical bleed: fill, run to operating temp with cabin heat on max, watch for the upper radiator hose to get hot (stat opened at ~105°C), let cool fully, recheck level, repeat. Vacuum-fill (Airlift) is best if available.

6

Verify, Bleed, Recheck Level

Start the engine — check for leaks at the housing. Watch for 'AC OFF DUE TO HIGH ENGINE TEMP' — if it appears, you have an air pocket or a leak. Cool fully, recheck the surge tank level, top off. Let it reach operating temp and confirm the upper hose gets hot (105°C thermostat opening).

All Done!

Test your repair before closing everything up. If something doesn't work right, double-check your steps.

⚠️ Common Mistakes to Avoid

  • • Not draining the coolant completely before starting the repair
  • • Failing to replace the thermostat gasket, leading to leaks
  • • Over-tightening bolts, which can crack the thermostat housing