Quick answer: Wiper Blade Replacement on a 2017–2025 Chrysler Pacifica is rated Easy and takes about 10–15 minutes. You'll need 1 tool for this job, and parts cost about $81. This guide walks you through the full job step by step, including the mistakes to avoid.
| Part Name |
Part Number |
Price |
Buy |
| Driver wiper blade, 26" |
Bosch 26A |
$32.99 |
|
| Passenger wiper blade, 20" |
Bosch 20B |
$32.99 |
|
| Rear wiper blade, 14" |
— |
$14.99 |
|
About prices: shown prices are typical retail averages and change frequently; cheaper alternatives may be available. Confirm the current price before buying.
💡 Pro tip: Order all parts at once to save on shipping
Step-by-Step Instructions
Follow these steps carefully
1
Confirm your sizes and buy the right blades
The 2017–2025 Pacifica — the minivan that replaced the Town & Country — takes 26 inches on the driver side, 20 inches on the passenger side, and 14 inches on the rear, and those numbers held steady through the 2021 facelift. Buy the two fronts as J-hook blades; the owner's manual itself describes the front connection as a release-tab fitting on the arm, which is the standard J-hook saddle with a flip tab. For the rear, get a 14-inch blade made for the Pacifica's pivot-pin rear mount — a generic hook blade won't fit back there. One caution while shopping: a few low-quality listings claim a 16-inch rear for the Pacifica, but 14 is what the charts and the factory sizing agree on, so don't get upsold.
🔧 Mechanic's note — Tom Becker
Fourteen on the rear, not sixteen — the 16-inch listings are low-quality upsells, and a generic hook blade won't fit the pivot-pin mount anyway. I buy the rear blade specifically made for the Pacifica's mount.
2
Park the wipers and lift the arms
Make sure the wipers are off so both arms rest at the base of the windshield — the Pacifica needs no service position; the manual's procedure starts with simply lifting the arm until it's fully upright.
3
Remove the old driver-side blade
Lift the driver arm to its full upright position. Support the arm the whole time; the manual cautions never to let an arm spring back against the glass without a blade on it.
🔧 Mechanic's note — Tom Becker
I flip the tab fully before I pull — I've learned a half-flipped release tab is the only reason these blades ever feel stuck, and the blade should walk off the hook with fingertip pressure.
4
Prep the new blade
Verify the new blade's saddle matches the release-tab hook fitting; if your blades include multiple adapters, fit the J-hook/release-tab one now per the leaflet. Wipe the windshield under the blade's path with glass cleaner while the arm is raised.
5
Install the new driver blade and verify the lock
Slide the new blade up onto the arm's hook until the release tab snaps back down into its locked position — the manual shows this tab in both locked and unlocked states, and you want it visibly locked. Tug the blade firmly along the arm to confirm it can't slide. Then lower the arm back to the windshield slowly, keeping your hand on it all the way down, exactly as the manual's caution demands: never let the bare arm spring back onto the glass or it may be damaged. Check the blade sits flat across its full 26 inches.
6
Do the passenger side, then the rear blade
Then the rear: unsnap the wiper arm pivot cap away from the glass first — the manual warns the arm cannot be fully raised unless you do this, and forcing it can damage the vehicle.
🔧 Mechanic's note — Ray Delgado
Unsnap that pivot cap before you touch the rear arm — the manual warns the arm can't fully raise with it on, and I've seen people force it and crack the cap housing. Cap first, then lift.
7
Test with washer fluid, front and rear
Spray washer fluid and run the fronts on low and high. If anything smears on the first wipe, re-check the front release tabs are fully locked and the rear pin clicked home; a half-seated rear pin lets the blade rock and skip.
All Done!
Test your repair before closing everything up. If something doesn't work right, double-check your steps.
⚠️ Common Mistakes to Avoid
- • Forcing the rear arm up without unsnapping the pivot cap first — the manual warns this can damage the vehicle.
- • Buying a 16-inch rear blade from a sloppy listing — the Pacifica takes a 14.
- • Leaving a front release tab half-flipped so the blade can walk off the hook at speed.