← Back to Cadillac XT6 Guides

2020–2024 Cadillac XT6

2020-2024 Cadillac XT6 — Spark Plug Replacement

By Tom Becker ✓ Certified Mechanic · Published Sep 21, 2026 · Updated Oct 22, 2026

🔧🔧🔧 Advanced 2–3 hours $115 DIY

Save $335 by doing it yourself! Shop cost: $450

Quick answer: Spark Plug Replacement on a 2020–2024 Cadillac XT6 is rated Advanced and takes about 2–3 hours. You'll need 9 tools for this job, and parts cost about $115. This guide walks you through the full job step by step, including the mistakes to avoid.

Quick Video Tutorial

Parts You Need

Total Cost
$115.00
Part Name Part Number Price Buy
Correct spark plug set for the gasoline/ICE engine in 2020-2024 Cadillac XT6; verify engine, heat range, gap, and VIN fitment — $115.00
Coil-boot seals or ignition coils only if inspection finds damage Optional — $35.00
Upper intake plenum gaskets Optional — —

About prices: shown prices are typical retail averages and change frequently; cheaper alternatives may be available. Confirm the current price before buying.

💡 Pro tip: Order all parts at once to save on shipping

Step-by-Step Instructions

Follow these steps carefully

1

Confirm the 3.6L LGX — the XT6's only engine — and work cold

It uses six iridium spark plugs, one per cylinder, each under its own coil-on-plug coil. Work on a stone-cold engine, park on level ground, and disconnect the negative battery terminal since you will be unplugging several sensors.

2

Pop off the engine cover to expose both banks

The LGX's large plastic engine cover lifts straight off its mounting posts with a firm upward pull — no bolts to remove. Work it off evenly so you do not snap a post.

🔧 Mechanic's note — Ray Delgado

I've been burned by this before: Work it off evenly so you do not snap a post. Your wallet will thank you.

3

Service the easy front bank first

Start with the three front coils: squeeze each connector's locking tab and pull it free, remove the small coil retaining bolt (10mm on the LGX), and pull the coil straight up with a gentle twist.

4

Lift the upper intake plenum to free the rear bank

Disconnect the throttle-body and sensor connectors, the PCV hoses, and any vacuum lines attached to the plenum — label each with tape and a marker. Remove the plenum bolts, lift the plenum straight up, and set it aside without stressing the attached hoses.

5

Swap the rear-bank plugs with the wells blown clean

Gap-check and hand-install the new plugs exactly as on the front bank, working one cylinder at a time so no well sits open longer than necessary. Unplug each coil connector, remove its 10mm retaining bolt, and pull the coil straight up.

6

Gap-check and hand-start every plug in the aluminum heads

Thread each plug in by hand using the extension — turn it backwards half a turn until the threads click into place, then clockwise; it should spin freely with finger pressure. Once finger-tight, seat it per the plug box instructions.

🔧 Mechanic's note — Ray Delgado

I keep a mental note on this one: Never invent a gap value: read the exact specification from the emissions sticker under the hood or the owner's manual, and measure each new iridium plug with a wire-type gap gauge without touching the center electrode.

7

Reseat the plenum, reconnect everything, and test drive

Lay the new (or inspected-good) plenum gaskets in place, lower the plenum squarely, and tighten its bolts evenly in a crisscross pattern so it seals flat. Reconnect every hose and connector using your labels and the reference photo — double-check the PCV lines, which are easy to miss under the plenum. A dab of dielectric grease inside each coil boot helps future removals. Reconnect the battery, start the engine, and listen: a hissing sound or rough idle means a vacuum leak at the plenum gasket or a missed hose — shut down and recheck. With a smooth idle, take a test drive with some light acceleration; steady power and no check-engine light mean the job is done.

All Done!

Test your repair before closing everything up. If something doesn't work right, double-check your steps.

⚠️ Common Mistakes to Avoid

  • • Reusing flattened or torn upper-plenum gaskets — the engine will idle rough from the vacuum leak.
  • • Forgetting to reconnect a PCV or vacuum hose under the plenum and chasing a phantom misfire afterward.
  • • Dropping a bolt or socket into an open intake port — cover every port the moment the plenum lifts.
  • • Overtightening plugs in the LGX's aluminum heads and stripping the threads.