2010-2019 Ford Taurus — Oil & Filter Change

🔧🔧 Moderate 30-60 minutes $55 DIY

Save $55 by doing it yourself! Shop cost: $110

Quick Video Tutorial

Parts You Need

Click links to purchase (we earn from qualifying purchases)

Total Cost

$60.00

Part Name	Part Number	Price	Buy
Correct engine oil for 2010-2019 Ford Taurus; verify viscosity, specification, and capacity in the owner manual	—	$45.00	Amazon
Engine oil filter for 2010-2019 Ford Taurus; verify engine and VIN fitment	—	$12.00	Amazon
New drain-plug washer or O-ring when the service procedure requires it	—	$3.00	Amazon

About prices: shown prices are estimates from typical Amazon listings and change frequently, and cheaper alternatives may be available. Confirm the current price on Amazon before buying.

💡 Pro tip: Order all parts at once to save on shipping

Step-by-Step Instructions

Follow these steps carefully

Confirm oil and filter fitment

Verify the exact engine, oil specification, viscosity, capacity, filter, drain-plug washer, and service interval for the 2010-2019 Ford Taurus. Park on level ground, let the engine cool enough to avoid burns, and gather a suitable drain pan.

Raise and secure the vehicle

Set the parking brake, chock the wheels, and use rated ramps or jack stands at the approved points for the 2010-2019 Ford Taurus. Never work beneath a vehicle supported only by a jack.

Drain the old oil

With the engine off, remove the fill cap and carefully loosen the drain plug on the 2010-2019 Ford Taurus. Let the oil drain fully into the pan, then inspect the plug, washer, oil, and pan for damage or unusual metal.

Replace the filter and washer

Remove the old filter from the 2010-2019 Ford Taurus, confirm its gasket came off, lightly oil the new gasket, install the filter by the specified hand-tight or torque procedure, and reinstall a new washer and drain plug to the exact OEM torque.

Refill and check for leaks

Add the specified oil in stages to the 2010-2019 Ford Taurus, wait, check the dipstick or electronic level on level ground, and do not exceed capacity. Start briefly, inspect the filter and plug for leaks, shut down, recheck the level, reset the maintenance reminder if appropriate, and recycle the used oil.

All Done!

Test your repair before closing everything up. If something doesn't work right, double-check your steps.

⚠️ Common Mistakes to Avoid

• Using the wrong viscosity, specification, or filter
• Raising the vehicle without rated stands, ramps, and wheel chocks
• Forgetting the old filter gasket or reusing a crushed drain-plug washer
• Over-tightening the filter or drain plug and damaging the housing or pan
• Checking level on an uneven surface or overfilling after a partial drain

Tools You'll Need

Floor jack, rated jack stands or ramps, and wheel chocks Correct oil-filter wrench or cap tool Drain pan, funnel, gloves, and eye protection Calibrated torque wrench for the drain plug and filter housing when specified

Torque Specifications

Critical specs — don't skip these!

Bolt	Nm	ft-lbs
	—	—

Important: Use a calibrated torque wrench. Over-tightening can strip threads. Under-tightening can loosen parts.

⚠️ Safety First!

• Informational DIY. EZ Car Fix is not a shop.
• Confirm the exact engine, oil viscosity/specification, capacity, filter, and drain-plug procedure before starting.
• Work on level ground with the vehicle supported by rated stands or ramps; never rely on a jack alone.
• Hot oil can burn. Wear gloves and eye protection, keep the drain pan stable, and dispose of used oil and the filter at an approved collection point.
• Do not overfill. Recheck the level after the engine rests and stop if the drain plug, filter seal, or oil-pressure warning indicates a leak or fault. This guide applies only to gasoline/ICE or hybrid vehicles with an engine; it is not for pure BEVs.