2018-2024 Honda Odyssey - Brake Pad Replacement

🔧🔧 Moderate 1-2 hours $85 DIY

Save $265 by doing it yourself! Shop cost: $350

Quick Video Tutorial

Parts You Need

Click links to purchase (we earn from qualifying purchases)

Total Cost

$85.00

Part Name	Part Number	Price	Buy
Front or rear brake pad set; verify axle and trim	—	$85.00	Amazon

💡 Pro tip: Order all parts at once to save on shipping

Step-by-Step Instructions

Follow these steps carefully

Confirm the axle and prepare the vehicle

Park the 2018-2024 Honda Odyssey on level ground, set the parking brake, chock the wheels, and compare the new pad set with the old parts. Identify whether the job is front or rear and follow the vehicle-specific electronic parking-brake service procedure if equipped.

Lift safely and remove the wheel

Loosen the lug nuts slightly, raise the 2018-2024 Honda Odyssey at the approved lift points, place it securely on jack stands, and remove the wheel. Keep the wheel and fasteners organized and support the hub if needed.

Inspect the brake assembly

Inspect the 2018-2024 Honda Odyssey rotor, caliper, hose, dust boots, slide pins, pad wear pattern, and backing hardware. Measure or compare rotor thickness and replace the rotor if it is below minimum thickness, deeply scored, cracked, or badly corroded.

Remove the caliper and old pads

Remove the caliper or caliper pins as specified for the 2018-2024 Honda Odyssey; support the caliper without stressing the hose. Remove the old pads and clips, noting the inner/outer orientation and the location of any wear sensor.

Service the slides and retract the piston

Clean the 2018-2024 Honda Odyssey bracket contact points and inspect the slide pins and dust boots. Lubricate only the specified sliding surfaces, then retract the piston with the correct tool while monitoring the master-cylinder reservoir and any electronic parking-brake requirements.

Install the new pads and reassemble

Install new abutment clips and the 2018-2024 Honda Odyssey brake pads in the original orientation. Refit the caliper, tighten fasteners to the exact service-manual torque, reinstall the wheel, and torque the lug nuts in a star pattern.

Restore hydraulic pressure and bed the pads

Before starting the 2018-2024 Honda Odyssey, pump the brake pedal until firm, verify the fluid level and parking-brake operation, then perform a slow controlled test. Bed the brake pads using the parts maker procedure and recheck for noise, pull, leaks, or warning lights.

All Done!

Test your repair before closing everything up. If something doesn't work right, double-check your steps.

⚠️ Common Mistakes to Avoid

• Ordering the wrong axle, brake package, or pad shape for the vehicle
• Letting the caliper hang from the brake hose or twisting the hose
• Compressing an electronic or screw-in rear piston without the required service procedure
• Installing pads or hardware with grease, rust, or dirt on the friction faces
• Skipping pedal pumping and the manufacturer-recommended bedding procedure

Tools You'll Need

Floor jack, jack stands, and wheel chocks Lug wrench or impact gun with torque wrench Metric/SAE socket set and ratchet Brake piston compressor or C-clamp Brake cleaner and wire brush High-temperature brake lubricant and safety glasses

⚠️ Safety First!

• Informational DIY. EZ Car Fix is not a shop.
• Support the 2018-2024 Honda Odyssey on rated jack stands on a level surface; never work under a vehicle supported only by a jack.
• Replace pads as an axle pair, verify the correct front or rear application, and keep grease or brake fluid off friction surfaces.
• Use the exact fastener and wheel torque for the year, trim, and brake package; put an electronic parking brake into its specified service mode before retracting a rear piston.
• Pump the pedal before moving, perform a controlled test, and do not drive if the pedal is soft, the vehicle pulls, or a warning light remains on.