EZCarFix DIY Auto Repair
← Back to BMW 330i xDrive Guides

2017–2024 BMW 330i xDrive

2017-2024 BMW 330i xDrive — Oil and Filter Change

By Tom Becker ✓ Certified Mechanic · Published Sep 24, 2026 · Updated Oct 14, 2026

🔧 Easy 30–60 minutes $69 DIY

Save $105 by doing it yourself! Shop cost: $174

Quick answer: Oil and Filter Change on a 2017–2024 BMW 330i xDrive is rated Easy and takes about 30–60 minutes. You'll need 8 tools for this job, and parts cost about $69. This guide walks you through the full job step by step, including the mistakes to avoid.

Quick Video Tutorial

Parts You Need

Total Cost
$69.00
Oil spec 2.0L turbo I4 (B46)
Capacity 5.6 qt with filter Viscosity 0W-20
Part Name Part Number Price Buy
BMW Longlife-approved 0W-20 engine oil — $62.00
B48 oil filter cartridge kit with O-rings — —
Replacement plastic oil drain plug — $7.00

About prices: shown prices are typical retail averages and change frequently; cheaper alternatives may be available. Confirm the current price before buying.

💡 Pro tip: Order all parts at once to save on shipping

Step-by-Step Instructions

Follow these steps carefully

1

Warm the B48 engine and park level

Run the B48 turbo engine for 3–5 minutes so the oil thins and drains fully, then switch it off and set the parking brake. The G20 has no dipstick, so park on perfectly level ground — the electronic oil-level reading and the sump drain both depend on it.

2

Remove the acoustic engine cover

Open the hood and lift the acoustic engine cover straight up off its ball-stud mounts. The black plastic oil filter housing is on top of the engine where it's easy to reach. Set the cover aside safely.

3

Replace the top-mounted filter cartridge

Place a rag around the housing and loosen the cap with a 27 mm socket, turning slowly so trapped oil drains back into the housing. Lift the cap out with the cartridge attached, pull the old element off the stem, and remove the old O-rings. Fit the new element into the housing and a new O-ring.

4

Raise the car and drain the composite sump

Chock the wheels, raise the front at the factory jacking points, and rest the car on jack stands. Let the oil drain to an occasional drip.

5

Fit a new drain plug and lower the car

Install a new plastic drain plug and tighten it to the service specification, then wipe the sump area clean so any future seepage is obvious. Lower the car back onto level ground and remove the drain pan.

6

Refill with 0W-20 and check the level

Pour in approximately 5.25 liters of BMW Longlife-approved 0W-20 through a clean funnel, holding back the last half-liter. Start the engine for about 30 seconds, switch off, wait one minute, then read the electronic oil level in the iDrive service menu and top up to the maximum mark.

7

Inspect the filter cap threads

If the old plastic filter cap shows worn or deformed threads, replace it — the cap is inexpensive insurance against a phantom leak. Otherwise refit everything removed and double-check the filler cap is tight.

8

Reset the oil service reminder and inspect for leaks

In iDrive, open Vehicle status, then Service required, and reset the engine oil item so the condition-based service timer restarts. Take a short drive, then look for drips at the sump plug and around the filter housing.

All Done!

Test your repair before closing everything up. If something doesn't work right, double-check your steps.

⚠️ Common Mistakes to Avoid

  • • Reusing the one-time plastic drain plug in the composite sump — it can crack and leak.
  • • Overtightening the plastic filter cap and damaging its threads.
  • • Pinching an O-ring during cap installation, causing a slow leak.
  • • Filling with oil that lacks the BMW Longlife approval for the B48 turbo.
  • • Forgetting the iDrive service reset, leaving the oil-change reminder on.