EZCarFix DIY Auto Repair
← Back to Lexus CT 200h Guides

2011–2017 Lexus CT 200h

2011-2017 Lexus CT 200h — Cabin Air Filter Replacement

By Tom Becker ✓ Certified Mechanic · Published Sep 21, 2026 · Updated Oct 22, 2026

🔧 Easy About 15 minutes $28 DIY

Save $72 by doing it yourself! Shop cost: $100

Quick answer: Cabin Air Filter Replacement on a 2011–2017 Lexus CT 200h is rated Easy and takes about 15 minutes. No tools are required for this job, and parts cost about $28. This guide walks you through the full job step by step, including the mistakes to avoid.

Quick Video Tutorial

Parts You Need

Total Cost
$28.00
Part Name Part Number Price Buy
Cabin air filter for 2011-2017 Lexus CT 200h; verify arrows, size, and VIN/trim fitment — $28.00

About prices: shown prices are typical retail averages and change frequently; cheaper alternatives may be available. Confirm the current price before buying.

💡 Pro tip: Order all parts at once to save on shipping

Step-by-Step Instructions

Follow these steps carefully

1

Park it and find the filter housing

Car off; sit in the passenger seat. On the 2011–2017 CT 200h the filter is in the HVAC housing behind the glove box: damper stay arm on its right, push-release cover, filter marked ‘UP’. No tools — just a replacement CT 200h filter.

2

Empty the glove box completely

Empty the glove box completely. Once unlatched it hangs low and anything left inside slides forward, blocking the filter cover. While empty, note the support arm hooked on a pin on the right wall — you'll unhook it next, so remember how it sits.

3

Unhook the support arm and drop the glove box

Slide the support arm off its pin. Press the box in front and rear to free its claws, then swing it fully open. Don't yank — the claw tabs snap if forced. If it won't swing, the arm is likely still on its pin.

🔧 Mechanic's note — Tom Becker

I've got the scars to prove it: Free the claws before you swing the box down — that thin glove box plastic snaps claw tabs if you yank. Gentle pressure front and rear is all it takes.

4

Release the filter cover

Look back: the plastic cover is the filter chamber door. Push inward on both ends, then pull it straight out — one piece, no screws. If stuck, the end tabs are catching — push them in further; prying with a screwdriver chews up the plastic.

5

Slide out the old filter and inspect the chamber

Pull the old filter and compare with the new — same size and shape. Note the ‘UP’ marks: installing it upside down is the most common mistake. Pull debris from the chamber bottom; left in place it clogs the filter early. Wipe dusty walls dry.

🔧 Mechanic's note — Ray Delgado

I made this mistake once — never again: Read the ‘UP’ marks before the old filter hits the trash. Upside down is the single most common mistake on this car.

6

Install the new filter and refit the cover

Slide the new filter in ‘UP’-side-up until fully seated. A half-seated filter whistles and rattles. Press the cover until both tabs click. If it won't click, the filter is crooked: pull it out a quarter inch, straighten, and try again rather than forcing it.

🔧 Mechanic's note — Tom Becker

I've trained my ears for this one: If the cover won't click, don't force it — pull the filter out a quarter inch and straighten it. A crooked filter is always the reason.

7

Rehang the glove box and verify airflow

Swing the glove box up and slide the arm onto its pin. Run the fan on high through dash, floor, and defrost. Whistling means the cover or filter isn't seated. Inspect early in dusty areas — a clogged filter causes weak airflow and musty smells.

All Done!

Test your repair before closing everything up. If something doesn't work right, double-check your steps.

⚠️ Common Mistakes to Avoid

  • • Installing the new filter upside down — the "UP" marks must point toward the top of the dash, not toward the floor
  • • Yanking the glove box down without first unhooking the support arm and disengaging the front and rear claws, which snaps the plastic tabs
  • • Prying the filter cover off with a screwdriver instead of pushing both ends inward, chewing up the cover edges
  • • Forgetting to slide the support arm back onto its pin, leaving the glove box flopping open instead of damped