EZCarFix DIY Auto Repair
← Back to Lexus CT 200h Guides

2011–2017 Lexus CT 200h

2011-2017 Lexus CT 200h — Wiper Blade Replacement

By Ray Delgado ✓ Certified Mechanic · Published Sep 21, 2026 · Updated Oct 22, 2026

🔧 Easy 15–20 minutes $66 DIY

Save $4 by doing it yourself! Shop cost: $70

Quick answer: Wiper Blade Replacement on a 2011–2017 Lexus CT 200h is rated Easy and takes about 15–20 minutes. You'll need 3 tools for this job, and parts cost about $66. This guide walks you through the full job step by step, including the mistakes to avoid.

Quick Video Tutorial

Parts You Need

Total Cost
$65.98
Part Name Part Number Price Buy
Driver wiper blade, 26" Bosch 26A $32.99
Passenger wiper blade, 18" Bosch 18B $32.99
Rear wiper blade, 8" — —

About prices: shown prices are typical retail averages and change frequently; cheaper alternatives may be available. Confirm the current price before buying.

💡 Pro tip: Order all parts at once to save on shipping

Step-by-Step Instructions

Follow these steps carefully

1

Buy the trio: 26, 18, and the oddball 8-inch rear

The CT 200h hybrid hatchback ran from 2011 to 2017 with no generation split, so the sizes are the same for every car in this range: a 26-inch blade on the driver side and an 18-inch blade on the passenger side, both on standard 9×3 mm J-hook arms. The rear is the special one — an 8-inch plastic-moulded blade with a vehicle-specific fitting. A generic 8-inch blade with a J-hook adapter will not latch onto the CT’s rear arm, so buy the rear blade listed specifically for the CT 200h. If any chart disagrees, measure the old blades before you spend a dollar.

🔧 Mechanic's note — Tom Becker

Take it from me: Buy the rear blade by the CT 200h listing, not by the 8-inch length. A generic 8-inch with a J-hook adapter will not latch — you'll be back at the store.

2

Prep the hatchback

Park level, parking brake on, fully off — on a hybrid, confirm the ‘ready’ indicator is out so the wipers can't spring to life. Clean the windshield and rear glass now — the tiny rear blade is unforgiving of a dirty screen.

3

Raise the front arms and protect the glass

Lift each front arm until it stands on its own, hand on it — stout springs, they snap back hard. Work one arm at a time; the 26-inch driver blade can swing into the other arm if you're careless.

4

Unhook the front blades

Turn a blade perpendicular to its arm and find the release tab on the center connector where it wraps the J-hook. Press the tab and slide the blade downward off the hook — straight off the end of the arm, no twisting. The J-hooks on the CT are a standard shape, so a blade that fights you is usually one where the tab hasn’t been pressed squarely; reset and try again rather than prying.

5

Fit the new front blades

The 26-inch blade goes on the driver side and the 18-inch on the passenger side — an 8-inch difference, so double-check before you click anything in, because the long blade on the wrong side is an obvious and ugly mistake. Slide each J-hook through the blade’s connector until it clicks, then tug the blade to confirm the lock. Let each blade pivot flat onto the glass before you move on.

🔧 Mechanic's note — Ray Delgado

Double-check the sizes before you click them in. The 26-inch blade on the passenger side looks ridiculous, and yes, I've done it.

6

Swap the little rear blade

Lift the rear arm and support it — its pivot doesn't like sideways stress. Release the old 8-inch blade from its fitting and click the new CT-specific blade into the same orientation. It should seat with a click; if loose, you've got the wrong blade.

🔧 Mechanic's note — Tom Becker

I've trained my ears for this one: If the new rear blade feels loose, stop forcing it — it's the wrong blade, not your technique. The right one seats with a positive click.

7

Test front and rear

Lower the arms onto the glass — never let them slap. Run the washers front and rear; each blade should clear its glass in one pass. Reseat the rear blade if it skips — any streak shows. Tug-check all three connectors after your first drive.

All Done!

Test your repair before closing everything up. If something doesn't work right, double-check your steps.

⚠️ Common Mistakes to Avoid

  • • Putting the 26-inch blade on the passenger side
  • • Buying a generic 8-inch J-hook blade for the rear instead of the CT-specific moulded blade
  • • Stress-testing the small rear arm pivot sideways
  • • Forgetting to switch the wiper stalk back to OFF on a hybrid