← Back to Audi Q5 Guides

2009–2017 Audi Q5

2009-2017 Audi Q5 — Spark Plug Replacement

By Tom Becker ✓ Certified Mechanic · Published Sep 21, 2026 · Updated Oct 14, 2026

🔧🔧🔧 Advanced 30–60 minutes (2.0T); 1–2 hours (V6) $115 DIY

Save $335 by doing it yourself! Shop cost: $450

Quick answer: Spark Plug Replacement on a 2009–2017 Audi Q5 is rated Advanced and takes about 30–60 minutes (2.0T); 1–2 hours (V6). You'll need 8 tools for this job, and parts cost about $115. This guide walks you through the full job step by step, including the mistakes to avoid.

Quick Video Tutorial

Parts You Need

Total Cost
$115.00
Part Name Part Number Price Buy
Correct spark plug set for 2009-2017 Audi Q5; verify engine, heat range, gap, and VIN fitment — $115.00
Coil-boot seals or ignition coils only if inspection finds damage Optional — $35.00

About prices: shown prices are typical retail averages and change frequently; cheaper alternatives may be available. Confirm the current price before buying.

💡 Pro tip: Order all parts at once to save on shipping

Step-by-Step Instructions

Follow these steps carefully

1

Prep — 2.0T, 3.2, or 3.0T under the hood

Park on level ground and let the engine cool completely. The 2009–2017 Q5 (first generation) came with three engines: the 2.0-liter turbo four (EA888) in all years, the 3.2-liter V6 (2009–2012), and the supercharged 3.0-liter V6 (2013–2017, including the SQ5).

2

Remove the cover and free the coil harness

Pull the plastic engine cover straight up off its rubber posts — no tools needed. Nothing else needs to come off; there is no intake or cowl removal on any of these engines.

3

Disconnect the battery

Loosen the negative battery cable clamp with a 10mm wrench, lift the cable off the post, and tuck it aside so it cannot spring back onto the terminal. You will lose radio presets and the clock, and the transmission may shift differently during a short relearn drive afterward.

🔧 Mechanic's note — Tom Becker

I tuck the loose cable behind the battery hold-down — if it springs back onto the post while your hands are down in the plug wells, you'll know about it.

4

Unplug the coils and pull them straight up

Release each coil's electrical connector by pressing its locking tab and pulling it straight off. A coil puller tool made for VW/Audi engines makes this much easier and prevents cracked coil housings. Set the coils aside in order.

🔧 Mechanic's note — Tom Becker

I've learned this one the hard way — a coil puller tool made for VW/Audi engines makes this much easier and prevents cracked coil housings.

5

Remove plugs and check the new gap

Blow dust and grit out of each open plug well with compressed air before loosening anything. Use a 16 mm spark plug socket with an extension — a thin-wall socket is recommended on the 2.0T because the wells are narrow. Turn counterclockwise to remove the old plugs. Check the gap on each new plug with a feeler gauge against the spec in the owner's manual or on the emissions sticker under the hood — never guess the gap. Use anti-seize only if the plug maker says to.

🔧 Mechanic's note — Ray Delgado

Shop habit of mine: Check the gap on each new plug with a feeler gauge against the spec in the owner's manual or on the emissions sticker under the hood — never guess the gap.

6

Hand-start and seat the new plugs

Thread each new plug in by hand several full turns before touching a ratchet — hand-starting is the only reliable defense against cross-threading the aluminum head. Once seated, tighten about a half-turn past finger-tight for a new washer-seat plug, following the plug maker's instructions.

🔧 Mechanic's note — Tom Becker

I've learned: this is the part people get wrong: Keep the force modest; the cylinder head is aluminum and a stripped thread turns a tune-up into a machine-shop repair.

7

Reseat coils, harness, and cover

Push each coil firmly down onto its plug until it bottoms out, reconnect each electrical connector until you hear it click locked, and reinstall the small screws holding the coil wiring harness to the valve cover.

8

Start up

Reconnect the battery, start the engine, and let it idle — it should be smooth with no warning lights.

All Done!

Test your repair before closing everything up. If something doesn't work right, double-check your steps.

⚠️ Common Mistakes to Avoid

  • • Yanking coils out at an angle and cracking the plastic housings
  • • Forgetting to undo the small screws holding the coil wiring harness to the valve cover before pulling the coils
  • • Reinstalling a coil without its connector fully clicked, causing an immediate misfire code