← Back to BMW X3 Guides

2021–2024 BMW X3

2021-2024 BMW X3 — Replace Air Filter

By Ray Delgado ✓ Certified Mechanic · Published Sep 21, 2026 · Updated Oct 22, 2026

🔧 Easy 30 minutes $20 DIY 2 views

Save $130 by doing it yourself! Shop cost: $150

Quick answer: Replace Air Filter on a 2021–2024 BMW X3 is rated Easy and takes about 30 minutes. You'll need 6 tools for this job, and parts cost about $20. This guide walks you through the full job step by step, including the mistakes to avoid.

Quick Video Tutorial

Parts You Need

Total Cost
$20.00
Part Name Part Number Price Buy
Genuine BMW Engine Air Filter Optional 13718691835 $35.97
Aftermarket Engine Air Filter 13718581691 $20.00

About prices: shown prices are typical retail averages and change frequently; cheaper alternatives may be available. Confirm the current price before buying.

💡 Pro tip: Order all parts at once to save on shipping

Step-by-Step Instructions

Follow these steps carefully

1

Locate the Air Filter Box

The 2021–2024 BMW X3 M40i (B58 3.0L turbo, 382-hp tune) engine air filter is in the airbox in the engine bay. Like the X6, the BMW uses a TORX-SCREW airbox lid — tools required (not hand clips). You'll need: new panel air filter, Torx driver (T25 typical — verify). The B58's 382-hp M40i tune is the high-output version — it needs unrestricted intake more than the base 40i. A dirty filter robs the M40i's performance. Open the hood and locate the airbox. The X3 M40i's B58 is the same engine as the X6 xDrive40i's — the airbox procedure is identical. Don't confuse with the cabin filter.

🔧 Mechanic's note — Ray Delgado

I grab the Torx driver before opening the hood — the X3 M40i's lid is Torx-screwed, not clipped, and I've seen people pry at it like it's a clip lid.

2

Open the Air Filter Housing (Torx screws)

Remove the Torx screws securing the airbox lid (same as the X6 — T25 typical). Count the screws so you don't miss one. The B58's airbox may have the intake tube attached — lift it enough to access the filter. Don't pry.

3

Remove the Old Filter

Lift the old panel filter out. Note the orientation. If it's dirty, your X3 M40i's B58 is down on power — the 382-hp tune needs clean air. The M40i's performance character means you'll feel a dirty filter (the B58 won't pull as hard). The high-output tune is more sensitive than the base B58. Check for debris.

4

Clean the Housing

Wipe the airbox clean. Remove dust and debris. Check the seal — the B58's turbo needs a perfect intake seal for the 382-hp tune. Don't touch the MAF sensor. A good seal means the M40i's turbo gets metered air.

5

Install the New Filter

Install the new panel filter, matching orientation. Ensure it seats with no gaps. The X3 M40i's B58 airbox is the same as the X6's — the filter should fit perfectly. The 382-hp tune demands a perfect seal — unmetered air hurts the high-output calibration. Verify the filter is for the B58 (not the 4-cylinder X3's).

6

Close and Secure

Replace the lid — reinstall all Torx screws, tighten evenly (don't over-torque plastic). Ensure a tight seal. Close the hood. Start the engine — the B58 should idle with its inline-6 smoothness. The X3 M40i should feel strong — the 382-hp B58 needs the clean filter to deliver. The Torx-screw airbox (same as X6) is BMW's design — have the driver ready. Replace every 20,000-30,000 miles. The M40i's high-output tune works the filter harder than the base — don't extend the interval.

🔧 Mechanic's note — Tom Becker

I tighten the Torx screws evenly in a cross pattern — I've cracked an airbox lid overtightening one corner, and the whistle it made drove the owner crazy.

All Done!

Test your repair before closing everything up. If something doesn't work right, double-check your steps.

⚠️ Common Mistakes to Avoid

  • • Forgetting to disconnect the battery before starting the repair
  • • Using incorrect tools, leading to damaged components
  • • Not properly sealing the air filter housing, causing air leaks