EZCarFix DIY Auto Repair
← Back to Cadillac DeVille Guides

2000–2005 Cadillac DeVille

2000-2005 Cadillac DeVille — Spark Plug Replacement

By Ray Delgado ✓ Certified Mechanic · Published Sep 21, 2026 · Updated Oct 22, 2026

🔧🔧🔧 Advanced 1-3 hours $115 DIY

Save $335 by doing it yourself! Shop cost: $450

Quick answer: Spark Plug Replacement on a 2000–2005 Cadillac DeVille is rated Advanced and takes about 1-3 hours. You'll need 4 tools for this job, and parts cost about $115. This guide walks you through the full job step by step, including the mistakes to avoid.

Quick Video Tutorial

Parts You Need

Total Cost
$115.00
Part Name Part Number Price Buy
Correct spark plug set for the gasoline/ICE engine in 2000-2005 Cadillac DeVille; verify engine, heat range, gap, and VIN fitment — $115.00
Coil-boot seals or ignition coils only if inspection finds damage Optional — $35.00

About prices: shown prices are typical retail averages and change frequently; cheaper alternatives may be available. Confirm the current price before buying.

💡 Pro tip: Order all parts at once to save on shipping

Step-by-Step Instructions

Follow these steps carefully

1

Confirm engine and plug fitment

The 2000-2005 DeVille's 4.6L Northstar V8 takes ACDelco 41-987 iridium plugs, pre-gapped to approximately 0.049-0.050 in — install as they come; do not re-gap. Buy eight. Scan for misfire codes (P0301-P0308) and note which bank is affected.

2

Cool and expose the plugs

Let the 4.6L cool and remove the beauty covers to expose the two coil cassettes. The rear bank sits tight against the firewall — use extensions back there — then unplug each cassette connector, labeling them front and rear.

3

Remove cassettes and clean wells

Unbolt each coil cassette and lift up — the plug boots come off with it. Blow compressed air down plug wells first; keep debris out of the cylinders. Inspect boots for cracks, brittleness, or carbon tracking — a bad boot misfires on a new plug.

🔧 Mechanic's note — Tom Becker

Inspect those cassette boots before you blame the plugs. On the Northstar, a cracked boot arcs to the head and misfires exactly like a worn plug — I've seen people do the whole plug job twice before checking the rubber.

4

Remove and install plugs

Use a 5/8 in spark plug socket on the ACDelco 41-987 plugs. Crack each plug loose and spin it out by hand, working carefully on the rear bank where swing room is minimal — a wobble extension is almost mandatory back there. Do not adjust the factory pre-set gap. Thread each new plug in by hand to protect the aluminum head threads, then tighten to the factory torque spec with a torque wrench. Never use an impact. Feed the socket to the rear-bank plugs by feel; the firewall leaves no room to see them directly.

5

Reconnect and verify

Seat each cassette so all four boots seal on their plugs; torque the bolts, reconnect the connectors and battery, then start the DeVille. Listen for a smooth idle. Road-test; a P030x on one cylinder means that cylinder's boot, since the cassette fires all four together.

All Done!

Test your repair before closing everything up. If something doesn't work right, double-check your steps.

⚠️ Common Mistakes to Avoid

  • • Using the wrong plug or assuming a pre-gapped plug needs no verification
  • • Blowing debris into an open cylinder or plug well
  • • Cross-threading a plug or tightening it without a torque wrench
  • • Overusing anti-seize or dielectric grease on the plug threads
  • • Mixing coil connectors or ignoring a misfire after reassembly