EZCarFix DIY Auto Repair
← Back to Chevrolet Astro Guides

1985–1994 Chevrolet Astro

1985-1994 Chevrolet Astro — Spark Plug Replacement

By Ray Delgado ✓ Certified Mechanic · Published Sep 21, 2026 · Updated Oct 22, 2026

🔧🔧🔧 Advanced 1-3 hours $115 DIY

Save $335 by doing it yourself! Shop cost: $450

Quick answer: Spark Plug Replacement on a 1985–1994 Chevrolet Astro is rated Advanced and takes about 1-3 hours. You'll need 3 tools for this job, and parts cost about $115. This guide walks you through the full job step by step, including the mistakes to avoid.

Quick Video Tutorial

Parts You Need

Total Cost
$115.00
Part Name Part Number Price Buy
Correct spark plug set for the gasoline/ICE engine in 1985-1994 Chevrolet Astro; verify engine, heat range, gap, and VIN fitment — $115.00

About prices: shown prices are typical retail averages and change frequently; cheaper alternatives may be available. Confirm the current price before buying.

💡 Pro tip: Order all parts at once to save on shipping

Step-by-Step Instructions

Follow these steps carefully

1

Confirm engine and plug fitment

This guide covers the 1985–1994 Chevrolet Astro with the 4.3-liter V6, which takes six plugs. For the 1992–1994 models with central port injection, the specified plug is the AC Delco CR43TS copper plug, gapped to 0.045 in. Earlier throttle-body-injection years used the R43TS family — check the underhood emissions sticker on your van, since it is the final authority for gap on these older engines. Confirm the part number against your VIN before buying. The Astro uses a distributor and plug wires, so budget for a wire set too if the originals are cracked or brittle.

2

Cool and expose the plugs

Let the engine cool completely. The 4.3L's iron heads hold heat. Disconnect the battery's negative terminal. Pull the doghouse, remove the air cleaner, and mark each plug wire with its cylinder number BEFORE removing anything. The firing order must go back exactly right.

🔧 Mechanic's note — Tom Becker

I've learned to mark each plug wire with its cylinder number BEFORE you pull anything — the firing order has to go back exactly right, and from the doghouse you can't see the distributor well enough to guess.

3

Pull the plug wires and inspect the wire and rotor

Pull each plug wire off by gripping the BOOT, never the wire. Inspect it and the rotor for carbon tracks, cracks, or a worn center button while you are in there, since distributor wear causes the same misfires new plugs are meant to fix.

🔧 Mechanic's note — Ray Delgado

I can tell you this: grip the BOOT, never the wire — decades of heat cycling make those old wires fragile, and one yank breaks the conductor inside. Twist gently to free a stuck boot.

4

Remove and install plugs

Using a 5/8 in. spark plug socket with extensions and a universal joint, work each plug out through the doghouse and wheel-well openings — a flexible approach beats removing more than you need to. Read the old plugs: oily deposits point to valve-guide wear common on high-mileage 4.3Ls. Confirm the new AC Delco CR43TS plugs are gapped to 0.045 in. with a wire gauge (or your sticker's spec for TBI years). Thread each plug in by hand until it seats, then tighten to the factory spec — snug, not gorilla-tight.

5

Reconnect and verify

Push each wire firmly back onto its plug until the boot seats, following your markings so the firing order is exactly right, then refit the doghouse cover and reconnect the battery. Start the Astro and let it idle: the 4.3L should settle into its characteristic smooth-but-burly idle. Take a test drive; fresh copper plugs restore the low-end grunt these vans are known for. If it misfires, recheck wire routing and distributor cap condition first — on these older ignition systems, the cap and rotor are frequent culprits alongside worn plugs.

All Done!

Test your repair before closing everything up. If something doesn't work right, double-check your steps.

⚠️ Common Mistakes to Avoid

  • • Using the wrong plug or assuming a pre-gapped plug needs no verification
  • • Blowing debris into an open cylinder or plug well
  • • Cross-threading a plug or tightening it without a torque wrench
  • • Overusing anti-seize or dielectric grease on the plug threads
  • • Mixing coil connectors or ignoring a misfire after reassembly