EZCarFix DIY Auto Repair
← Back to Chevrolet Trailblazer Guides

2021–2024 Chevrolet Trailblazer

2021-2024 Chevrolet Trailblazer — Spark Plug Replacement

By Tom Becker ✓ Certified Mechanic · Published Sep 21, 2026 · Updated Oct 22, 2026

🔧🔧🔧 Advanced 1-3 hours $115 DIY

Save $335 by doing it yourself! Shop cost: $450

Quick answer: Spark Plug Replacement on a 2021–2024 Chevrolet Trailblazer is rated Advanced and takes about 1-3 hours. You'll need 4 tools for this job, and parts cost about $115. This guide walks you through the full job step by step, including the mistakes to avoid.

Quick Video Tutorial

Parts You Need

Total Cost
$115.00
Part Name Part Number Price Buy
Correct spark plug set for the gasoline/ICE engine in 2021-2024 Chevrolet Trailblazer; verify engine, heat range, gap, and VIN fitment — $115.00
Coil-boot seals or ignition coils only if inspection finds damage Optional — $35.00

About prices: shown prices are typical retail averages and change frequently; cheaper alternatives may be available. Confirm the current price before buying.

💡 Pro tip: Order all parts at once to save on shipping

Step-by-Step Instructions

Follow these steps carefully

1

Confirm engine and plug fitment

Confirm your 2021-2024 Trailblazer's exact engine before ordering — the two turbo threes take different plugs. 1.2L: NGK LNAR8AIX-P (stock 97977), pre-gapped 0.028 in. 1.3L: NGK ILNFR9B7G, pre-gapped 0.030 in. Both are slim 12mm-thread iridium plugs with a 14mm hex, so a standard 5/8 in. socket will not fit. Scan for misfire codes first and inspect the coil boots.

🔧 Mechanic's note — Ray Delgado

Ask me how I know: Confirm your 2021-2024 Chevrolet Trailblazer's exact engine before ordering, because the two turbo threes take different plugs: the 1.2L uses the NGK LNAR8AIX-P (stock 97977), pre-gapped at 0.028", while the 1.3L uses the NGK ILNFR9B7G, pre-gapped at 0.030".

2

Cool and expose the plugs

Each coil is held by a single small bolt with a locking electrical connector; release the lock and pull the connector body, never the wiring.

🔧 Mechanic's note — Ray Delgado

Each coil is held by a single small bolt with a locking electrical connector; release the lock and pull the connector body, never the wiring. I don't skip this anymore.

3

Remove the coils

Remove each coil's single bolt and lift the coil straight up out of its well, keeping the three coils in cylinder order so each returns to its original plug.

4

Remove and install plugs

Remove each old plug with a 14 mm thin-wall spark-plug socket and compare its deposits and electrode wear to the new NGK; on the turbo engine expect some dark carbon, but heavy oil fouling on one plug points at that cylinder's valve seals. Start every new plug by hand, turning it backward a half-turn first until the threads click into place so the small aluminum threads never cross-thread. Never use an impact for final seating. Tighten to the manufacturer's spec in your owner's manual — these small 12 mm plugs take far less torque than old 14 mm plugs. Do not re-gap the preset electrodes.

🔧 Mechanic's note — Ray Delgado

I've fixed the damage from skipping this: Start every new plug by hand, turning it backward a half-turn first until the threads click into place so the small aluminum threads never cross-thread.

5

Reconnect and verify

Seat each coil fully onto its plug, reinstall its bolt, and reconnect every coil connector until it clicks. Refit the engine cover. Start the Trailblazer and confirm a smooth idle with no check-engine light, then scan for misfire codes (P0300-P0303) after a test drive that includes boost — the turbo three exposes a weak coil under load. Stop and recheck if any thread bound during installation, a coil boot tore, or a misfire code returns.

All Done!

Test your repair before closing everything up. If something doesn't work right, double-check your steps.

⚠️ Common Mistakes to Avoid

  • • Using the wrong plug or assuming a pre-gapped plug needs no verification
  • • Blowing debris into an open cylinder or plug well
  • • Cross-threading a plug or tightening it without a torque wrench
  • • Overusing anti-seize or dielectric grease on the plug threads
  • • Mixing coil connectors or ignoring a misfire after reassembly