Quick answer: Spark Plug Replacement on a 2003–2007 Infiniti G35 is rated Advanced and takes about 2.5 to 4 hours. You'll need 7 tools for this job, and parts cost about $115. This guide walks you through the full job step by step, including the mistakes to avoid.
| Part Name |
Part Number |
Price |
Buy |
| Correct spark plug set for the gasoline/ICE engine in 2003-2007 Infiniti G35; verify engine, heat range, gap, and VIN fitment |
— |
$115.00 |
|
| Coil-boot seals or ignition coils only if inspection finds damage Optional |
— |
$35.00 |
|
| PCV valve |
— |
— |
|
| Upper intake plenum gasket set |
— |
— |
|
About prices: shown prices are typical retail averages and change frequently; cheaper alternatives may be available. Confirm the current price before buying.
💡 Pro tip: Order all parts at once to save on shipping
Step-by-Step Instructions
Follow these steps carefully
1
Disconnect the battery and survey the VQ35DE's split access
Disconnect the negative cable on a cold G35 — you disturb the throttle body wiring here, and a battery-off job skips the relearn. The upper plenum covers the driver-side coils: pull the engine cover and take stock — passenger bank exposed, driver bank underneath.
2
Clear the passenger bank — the easy three plugs
Rock each coil connector off, remove the 10mm bolt, and pull the coil up with a twist. Blow compressed air down each open well first — grit in an open cylinder is unforgivable. Crack the three passenger plugs loose with a 5/8-inch socket and extension.
3
Unbolt the upper intake plenum to free the driver bank
Unplug the throttle body and sensors, disconnect the intake tube, and release the PCV hose. Remove the plenum bolts and the two stud nuts, lift the plenum straight up — you can usually tie it aside. Stuff each exposed intake port with a clean rag.
4
Service the newly exposed driver-side plugs
Pull the three driver-side coils the same way, blow out the wells, and remove the remaining plugs. With the plenum off, replace the PCV valve — a stuck PCV is a classic VQ oil-consumption culprit. Plenum gaskets get replaced, not reused.
🔧 Mechanic's note — Ray Delgado
I budget extra time for this: The driver-side rear plug is the one that eats sockets — use a magnetic spark plug socket and a locking extension on that cylinder, or you'll spend twenty minutes fishing.
5
Gap the new plugs and hand-install all six
Gap each plug with a feeler gauge per the emissions sticker. Thread every plug in by hand until the washer seats, restarting at any hint of binding. Snug each a quarter to a half turn past contact — aluminum heads strip if you get aggressive.
🔧 Mechanic's note — Ray Delgado
I tell everyone doing this job: replace the PCV valve and the plenum gaskets while you're in there — you've already done ninety percent of the labor, and a dried-out gasket will have you pulling the plenum a second time.
6
Seat the plenum on fresh gaskets and reconnect everything
Seat the coils and click every connector home. Pull the rags from the ports — count them — and set the plenum onto fresh gaskets. Snug bolts lightly in a crisscross; overtightening whistles. Reconnect the throttle body, sensors, PCV hose, and intake tube.
7
Start it up, hunt for vacuum leaks, and road test
Reconnect the battery and start it; idle should settle smooth. A hunting idle or hissing means a vacuum leak — shut down and recheck. Take a 15-minute drive with varied throttle; the ECU relearns idle trim. No check-engine light means the job is done.
All Done!
Test your repair before closing everything up. If something doesn't work right, double-check your steps.
⚠️ Common Mistakes to Avoid
- • Trying to reach the driver-side plugs without removing the upper plenum — the collector sits directly over those coils and there is no shortcut.
- • Reusing the old plenum gaskets — they're compressed and heat-cycled, and a vacuum leak after reassembly will idle worse than the old plugs did.
- • Dropping a plenum bolt or a rag into an open intake port while the plenum is off — stuff every port with a clean rag the moment it's exposed.