Quick answer: Spark Plug Replacement on a 2013–2020 Lexus GS is rated Advanced and takes about 2–4 hours. You'll need 5 tools for this job, and parts cost about $115. This guide walks you through the full job step by step, including the mistakes to avoid.
| Part Name |
Part Number |
Price |
Buy |
| Correct spark plug set for the gasoline/ICE engine in 2013-2020 Lexus GS350; verify engine, heat range, gap, and VIN fitment |
— |
$115.00 |
|
| Coil-boot seals or ignition coils only if inspection finds damage Optional |
— |
$35.00 |
|
About prices: shown prices are typical retail averages and change frequently; cheaper alternatives may be available. Confirm the current price before buying.
💡 Pro tip: Order all parts at once to save on shipping
Step-by-Step Instructions
Follow these steps carefully
1
Prep — identify your GS engine first
GS 350's 3.5-liter 2GR-FSE V6 is the hardest: six plugs, rear three buried under the plenum. The 2.0T 8AR-FTS four and 2.5L 2AR-FSE / 3.5L 2GR-FXE hybrids have plugs under the cover. Check the badge and underhood label first.
2
Access — V-bank cover off; V6 rear bank needs the intake plenum
Pull the V-bank engine cover off. On the 2.0T and 2.5 hybrid, four coils are exposed. On the 3.5L V6s, rear bank hides under the intake plenum: remove the intake ducting, throttle body, vacuum hoses, and plenum, tracking every hose.
🔧 Mechanic's note — Ray Delgado
I've done GS 350 plug jobs that book at four hours because of that rear-bank plenum. Bag and label every vacuum hose and bolt you remove — one forgotten hose means a lean code and a comeback.
3
Coil pack removal — press-tab connectors, 10mm bolts
Each coil is held by one 10mm bolt. Disconnect every connector first (press the locking tab, slide off), then unbolt and pull each coil straight up. On the V6, rear-bank connector plastic gets brittle with heat and age.
4
Plug removal — blow out wells, then unthread
Blow out each well. The 2GR-FSE uses 14mm plugs — use a thin-wall 14mm socket and extension. Break each plug loose, then spin it out. D4-S plugs have three side straps; a carbon-fouled plug means that cylinder runs rich.
5
Install new plugs — OEM-style multi-electrode, gap per manual
Use the OEM-style multi-ground-electrode plug — not a generic single-electrode substitute. Never invent a gap: check against the underhood sticker with a wire gauge. Thread every plug in by hand until seated, then apply only the maker's small final tightening — over-torquing strips aluminum threads.
6
Reassembly — coils, plenum, hoses, and covers
Seat every coil, reinstall 10mm bolts, and click each connector home. On the V6s, reinstall the plenum: replace flattened or torn gaskets, torque bolts in sequence, and reconnect every vacuum hose and intake ducting — a forgotten hose causes a lean code and rough idle.
7
Verification — start, idle check, and interval note
Start the engine — smooth idle, no check-engine light — then test-drive hard. On the 2GR-FSE, Lexus calls for fresh plugs roughly every 60,000 miles. A misfire code right after the job means rechecking coil connectors and (V6) vacuum hoses before suspecting a plug.
All Done!
Test your repair before closing everything up. If something doesn't work right, double-check your steps.
⚠️ Common Mistakes to Avoid
- • Attempting the GS 350's rear bank without removing the intake plenum — the coils are physically unreachable otherwise.
- • Reusing flattened plenum gaskets on the V6, causing vacuum leaks and lean codes.
- • Using generic single-electrode plugs in a D4-S V6 instead of the OEM-style multi-ground-electrode design.