EZCarFix DIY Auto Repair
← Back to Audi S4 Guides

2010–2024 Audi S4

2010-2024 Audi S4 — Cabin Air Filter Replacement

By Ray Delgado ✓ Certified Mechanic · Published Sep 21, 2026 · Updated Oct 22, 2026

🔧 Easy 20–25 minutes (B8/B8.5); 30–40 minutes (B9) $28 DIY

Save $72 by doing it yourself! Shop cost: $100

Quick answer: Cabin Air Filter Replacement on a 2010–2024 Audi S4 is rated Easy and takes about 20–25 minutes (B8/B8.5); 30–40 minutes (B9). You'll need 1 tool for this job, and parts cost about $28. This guide walks you through the full job step by step, including the mistakes to avoid.

Quick Video Tutorial

Parts You Need

Total Cost
$28.00
Part Name Part Number Price Buy
Cabin air filter for 2010-2024 Audi S4; verify arrows, size, and VIN/trim fitment — $28.00

About prices: shown prices are typical retail averages and change frequently; cheaper alternatives may be available. Confirm the current price before buying.

💡 Pro tip: Order all parts at once to save on shipping

Step-by-Step Instructions

Follow these steps carefully

1

Identify your chassis: B8 or B9

The 2010–2024 S4 covers two chassis. B8/B8.5 (2010–2016): filter under the glove box behind a foam panel. 2016 and older is B8/B8.5; 2017 and newer is B9.

2

Make room: seat back, mats out

Open the passenger door and slide the seat all the way back — you'll work on your back in the footwell. Pull the floor mat out too.

3

B8/B8.5: remove the foam cover (three thumbscrews)

On 2010-2016 cars, look up under the glove box: a black foam cover held by three thumbscrews. Unscrew them and pull the cover off. Behind it, slide the white cover right, then remove the gray foam near the fan motor to expose the filter slot.

4

B9: pull the felt liner and tackle the six-clip cover

On 2017–2024 cars, remove the felt liner in the rear of the footwell (two pull-out clips). Behind it sits the filter cover — a boomerang-shaped panel held by six clips.

🔧 Mechanic's note — Tom Becker

I've trained my ears for this one: That last top-right clip on the B9 cover is a knuckle-buster. Work it gently — if you force it and it snaps, the cover never seats right again and you'll hear it whistle forever.

5

Pull the old filter and read its arrow

Slide the old filter out level so dust doesn't fall into the blower. Check the airflow arrow on its frame and photograph the orientation — the new filter must match exactly. B8 cars take a rectangular filter; on the B9 note the tight, curved space.

6

Install the new filter (B9: pre-bend it)

Slide the new filter in with its arrow matching the old one, pushing it fully home. B9 tip: pre-bend the filter into a slight curve first — the tight housing takes a curved filter far more easily.

🔧 Mechanic's note — Ray Delgado

The pre-bend trick is real. I fought one of these B9 filters flat for ten minutes before an owner showed me the curve — it slides right in.

7

Close everything up and verify the seal

B8: refit the gray foam, slide the cover until it latches, replace the foam panel, and tighten the thumbscrews. B9: press the cover on — confirm six clips engage or it whistles. Refit the liner. Run the blower and listen for whistling. Every 15,000 miles.

All Done!

Test your repair before closing everything up. If something doesn't work right, double-check your steps.

⚠️ Common Mistakes to Avoid

  • • Forcing the B9's top-right corner clip and snapping it — it's the hardest to reach and the easiest to break
  • • On the B8, forgetting the gray foam piece behind the white cover, or sliding the white cover back the wrong way
  • • Leaving any B9 cover clip unlatched, which causes an audible air leak/whistle from the footwell