Quick answer: Spark Plug Replacement on a 2010–2024 Audi S4 is rated Advanced and takes about 2–3 hours (B8), 1–2 hours (B9). You'll need 6 tools for this job, and parts cost about $115. This guide walks you through the full job step by step, including the mistakes to avoid.
| Part Name |
Part Number |
Price |
Buy |
| Correct spark plug set for the gasoline/ICE engine in 2010-2024 Audi S4; verify engine, heat range, gap, and VIN fitment |
— |
$115.00 |
|
| Coil-boot seals or ignition coils only if inspection finds damage Optional |
— |
$35.00 |
|
About prices: shown prices are typical retail averages and change frequently; cheaper alternatives may be available. Confirm the current price before buying.
💡 Pro tip: Order all parts at once to save on shipping
Step-by-Step Instructions
Follow these steps carefully
1
Identify your generation and let the engine cool
B8/B8.5 (2010–2016): 3.0L supercharged V6. B9 (2017–2024): 3.0L single-turbo V6 (EA839). Six plugs either way — the 2.9L twin-turbo is an RS4/RS5 engine. Work on a completely cold engine with the parking brake set.
2
Clear access on the B8 supercharged engine
Remove the engine cover and airbox-to-throttle tube — loosen its clamps and move it aside. The supercharger stays put. Unbolt the Torx screws on each bank's coil harness and slide the harness off. Disconnect the negative battery terminal.
3
Clear access on the B9 turbo engine
Remove the engine cover. Move the passenger-side inlet hose aside and swing the PCV hose clear for the driver-side coils. Each B9 coil is held by a T30 Torx screw. The turbo stays put. Disconnect the negative battery terminal.
4
Unplug and remove the six ignition coils
Slide back the red tab and push each connector off. Remove the retaining screws — Torx on B8, T30 per coil on B9. Pull each coil up, twisting stuck ones; never lever against the valve cover. Keep them in order.
🔧 Mechanic's note — Tom Becker
I've pulled hundreds of VAG coils, and the twist-and-pull saves valve covers. Guys who lever against the cover crack it every time — aluminum doesn't forgive.
5
Remove the old plugs and install the new ones
Blow debris out of each plug well before loosening anything. Use a slim 14mm 12-point spark plug socket on an extension — a standard thick-wall socket can jam in these wells. Remove the six old plugs counterclockwise and keep them in order to compare. Check the gap in the owner's manual or on the underhood emissions sticker and verify each new plug with a feeler gauge, adjusting only the ground strap. Thread each plug in by hand, then tighten until the washer seats plus about a quarter to a half turn. The heads are aluminum — never overtighten.
🔧 Mechanic's note — Ray Delgado
I always check this before I pick up a wrench: Buy the slim 14mm 12-point spark plug socket before you start. A standard thick-wall socket wedges in these wells and turns a 20-minute job into a fight.
6
Reinstall the coils and intake plumbing
Press each coil onto its plug, snug the screws, and reconnect each wiring plug — slide the red lock back and tug to confirm. Refit intake plumbing, tightening the clamps; an air leak causes rough idle. Reconnect the battery and refit the engine cover.
7
Start up and verify under load
Start the engine: smooth idle, no warning lights. Test-drive with firm acceleration — boost exposes a weak coil or loose connector. Flashing check-engine light means an active misfire: stop and recheck the connectors. Note the mileage; these plugs typically last 60,000 miles.
All Done!
Test your repair before closing everything up. If something doesn't work right, double-check your steps.
⚠️ Common Mistakes to Avoid
- • Assuming the supercharger must come off on the B8 — it does not; only the intake tube and airbox need moving.
- • Using a thick-wall socket that jams in the narrow plug wells instead of a slim 14mm 12-point socket.
- • Forgetting to slide the red connector locks back into place, so a coil plug works loose later.
- • Leaving an intake clamp loose on reassembly, causing an air leak and rough idle.