EZCarFix DIY Auto Repair
← Back to Audi S4 Guides

2010–2024 Audi S4

2010-2024 Audi S4 — Engine Air Filter Replacement

By Tom Becker ✓ Certified Mechanic · Published Sep 21, 2026 · Updated Oct 22, 2026

🔧 Easy 15–25 minutes $35 DIY

Save $75 by doing it yourself! Shop cost: $110

Quick answer: Engine Air Filter Replacement on a 2010–2024 Audi S4 is rated Easy and takes about 15–25 minutes. You'll need 2 tools for this job, and parts cost about $35. This guide walks you through the full job step by step, including the mistakes to avoid.

Quick Video Tutorial

Parts You Need

Total Cost
$35.00
Part Name Part Number Price Buy
Engine air filter for 2010-2024 Audi S4; verify engine, housing shape, and VIN fitment — $35.00

About prices: shown prices are typical retail averages and change frequently; cheaper alternatives may be available. Confirm the current price before buying.

💡 Pro tip: Order all parts at once to save on shipping

Step-by-Step Instructions

Follow these steps carefully

1

Identify B8 supercharged vs B9 turbo layout

Check which S4 you have — the airbox moved between generations. B8 (2010–2016): front of the bay, driver's side, ahead of the supercharger. B9 (2017–2024): passenger side. Both use Torx T25; B8 layout below, with B9 notes where they diverge.

2

Free the inlet duct (B8: radiator cover first)

B8: remove the upper radiator cover — press each push-pin center in and lift it off — then remove the inlet duct (two T25 screws). B9: free the inlet ducting at the front. Set the duct aside clean.

3

Remove the lid screws and lift the lid

Back out the T25 lid screws — seven on the B8 — leaving each loose in its hole. Loosen the intake-hose clamp and lift the lid; on the B8 the filter is clipped to the lid's underside via a coupler, so unclip it.

🔧 Mechanic's note — Tom Becker

My two cents on this step: That B8 filter is clipped to the lid's underside, and it surprises everyone. Lift the lid slow — if you rip it straight up, you'll tear the element or the coupler.

4

Remove the old element and clean the base

Lift the old element out. On the B8, note how the filter's base bosses engaged the lid coupler — the replacement must seat identically. Vacuum the base; the B8's inlet collects leaves. Inspect sealing edges and base for cracks.

5

Seat the new filter and re-engage the coupler

Fit the new element in its recess, then re-engage the B8 coupler to the lid first — it must clip positively or the filter shifts. Confirm the sealing edge lies flat. On the B9, drop the panel in flush.

6

Refit the lid, duct, and covers

Set the lid down so every T25 screw drops into its hole. Start screws by hand, then snug gently; they strip easily. Refit the duct and cover, locking each push-pin center back out, then retighten the hose clamp.

🔧 Mechanic's note — Ray Delgado

I've learned this the hard way: Run those T25s in by hand first. They thread into plastic and strip with almost no effort, and a stripped boss means a whistling lid forever.

7

Start up and confirm intake behavior

Start the engine; listen for airbox whistling or radiator-cover rattling — missed screws or unseated pins. Confirm no warning lights. Test-drive with firm acceleration: the B8 should pull cleanly, the B9 build boost smoothly. Replace every 30,000 to 40,000 miles.

All Done!

Test your repair before closing everything up. If something doesn't work right, double-check your steps.

⚠️ Common Mistakes to Avoid

  • • Treating the B8 and B9 cars as identical — the B8 (2010–2016) 3.0T supercharged airbox sits at the front of the bay on the driver's side with seven T25 lid screws, while the B9 (2017–2024) 3.0T turbo box is on the passenger side with a different screw layout.
  • • Skipping the upper radiator cover removal on the B8 — the push-pin clips release by pressing their centers, and yanking the cover without releasing them breaks the pins.
  • • Overtightening the T25 screws into the plastic airbox on reassembly — they need only a gentle snug, and stripped bosses mean a new airbox.