EZCarFix DIY Auto Repair
← Back to BMW 328i Guides

2008–2013 BMW 328i

2008-2013 BMW 328i - Spark Plug Replacement

By Tom Becker ✓ Certified Mechanic · Published Sep 21, 2026 · Updated Oct 22, 2026

🔧🔧 Moderate 1-2 hours $55 DIY

Save $245 by doing it yourself! Shop cost: $300

Quick answer: Spark Plug Replacement on a 2008–2013 BMW 328i is rated Moderate and takes about 1-2 hours. You'll need 7 tools for this job, and parts cost about $55. This guide walks you through the full job step by step, including the mistakes to avoid.

Quick Video Tutorial

Parts You Need

Total Cost
$54.95
Part Name Part Number Price Buy
TRQ SPA02135 Spark Plug Set SPA02135 $54.95
NGK Laser Platinum Spark Plug Set Optional NGETK00121 $71.95
BMW / Bosch OE Spark Plugs 12-12-2-158-253 / FR7NPP332 —

About prices: shown prices are typical retail averages and change frequently; cheaper alternatives may be available. Confirm the current price before buying.

💡 Pro tip: Order all parts at once to save on shipping

Step-by-Step Instructions

Follow these steps carefully

1

Cool the engine

The 2008–2013 BMW 328i (E90, N52 inline-6) uses BMW 12-12-2-158-253 / Bosch FR7NPP332 multi-electrode plugs. These are PRESET — do not gap multi-electrode plugs (you'll damage them). Torque: CONFLICT — sources cite 23 N·m vs 30 N·m. Do NOT pick one without the FSM — check your BMW service manual. You'll need: 6x correct plugs, 14mm THIN-WALL 12-point spark plug socket (mandatory — a standard socket won't fit the N52's deep plug wells), extensions. Critical: let the N52 cool — aluminum head. Known quirk: the N52's coil lever can cause misfires if not seated properly — ensure coils click fully.

🔧 Mechanic's note — Tom Becker

I let the 328i cool and I reach for my torque wrench before I touch a plug — the N52 head is aluminum, and I have seen a plug installed by feel strip threads that cost a thousand dollars to fix with a timesert.

2

Access the ignition coils

Remove the engine cover (it pulls off). Remove the cabin filter housing/cowl panel if it's blocking the rear coils (common on the E90). Note the coil lever design — it's a BMW quirk.

3

Remove one coil at a time

The N52's coil lever must be fully disengaged — if you yank without flipping the lever, you'll break it. Inspect the boots.

4

Remove the old spark plug

Use the 14mm THIN-WALL 12-point socket to remove the old plug. A standard 14mm won't fit — the N52's plug wells are narrow, so the thin-wall 12-pt is mandatory. Turn counterclockwise. The old Bosch FR7NPP332 multi-electrode should show normal wear. Don't drop anything into the wells.

5

Gap and hand-thread the new plug

The new multi-electrode plugs are PRESET — do NOT gap them. Inspect the new plug to ensure the electrodes weren't bent in shipping. NEVER use a wrench to start — the aluminum head strips. The 14mm thin-wall socket is for removal/installation, but hand-start first.

6

Torque to specification (verify!)

Torque to BMW spec — but there's a CONFLICT: 23 N·m vs 30 N·m appear in sources. Do NOT guess. Check your BMW FSM or a reliable N52-specific source for the correct value. Use a torque wrench with the thin-wall 12-pt socket. Do not over-torque.

7

Reinstall the coil (seat the lever!)

The N52's coil lever MUST be fully engaged — a partially seated coil causes the famous N52 misfire. Ensure each coil clicks/locks. Repeat for all 6 cylinders, one at a time. Reinstall the cowl panel/cabin filter housing if you removed it.

🔧 Mechanic's note — Tom Becker

I reinstall the 328i coil and I seat the lever until it clicks — I have seen a coil that felt seated work loose from engine vibration and throw a misfire code a week later. No click, no done.

8

Reassemble and test

Reinstall the engine cover. Start the engine — the N52 inline-6 should idle buttery smooth. Check for misfire codes. The N52's coil-lever quirk means a misfire after a plug change is almost always a poorly seated coil — recheck the levers first. Test drive: the 328i should pull smoothly. The multi-electrode plugs last ~100k miles. If you have persistent misfires, the coils themselves are the likely culprit (N52 coils are a wear item). The 14mm thin-wall 12-pt socket is a BMW-specific tool — keep it for next time.

🔧 Mechanic's note — Tom Becker

I never skip the post-plug test drive on a 328i — a coil not fully seated will misfire under load, and it never shows at idle in the driveway. I drive it, load the engine, and watch for the shudder.

All Done!

Test your repair before closing everything up. If something doesn't work right, double-check your steps.

⚠️ Common Mistakes to Avoid

  • • Not properly gapping the new spark plugs
  • • Failing to torque the spark plugs to manufacturer specifications
  • • Not using dielectric grease on the spark plug boots