EZCarFix DIY Auto Repair
← Back to BMW X1 Guides

2016–2024 BMW X1

2016-2024 BMW X1 — Replace Wiper Blades

By Ray Delgado ✓ Certified Mechanic · Published Sep 21, 2026 · Updated Oct 22, 2026

🔧 Easy 15 minutes $66 DIY

Save $34 by doing it yourself! Shop cost: $100

Quick answer: Replace Wiper Blades on a 2016–2024 BMW X1 is rated Easy and takes about 15 minutes. You'll need 1 tool for this job, and parts cost about $66. This guide walks you through the full job step by step, including the mistakes to avoid.

Quick Video Tutorial

Parts You Need

Total Cost
$65.98
Part Name Part Number Price Buy
Driver wiper blade, 26" Bosch 26A $32.99
Passenger wiper blade, 16" Bosch 16B $32.99
Rear wiper blade, 13"-14" (measure old blade) — —

About prices: shown prices are typical retail averages and change frequently; cheaper alternatives may be available. Confirm the current price before buying.

💡 Pro tip: Order all parts at once to save on shipping

Step-by-Step Instructions

Follow these steps carefully

1

Service position (if needed)

The BMW X1 xDrive28i (F48 generation, 2016-2022) needs its wipers in service position before the arms can be lifted — they park tucked under the hood edge. Switch the ignition on, then off, and within about 10 seconds push the wiper stalk up and hold it for a few seconds until the arms park upright. Never force the arms up from the parked position; you can damage the arms or the hood edge. (For the 2023+ U11 X1, confirm sizes against your owner's manual — measure the old blades before ordering.)

🔧 Mechanic's note — Tom Becker

I do the stalk procedure to get service position — I've seen someone force an X1 arm up from parked and crease the hood edge, which is an expensive lesson.

2

Lift the wiper arm

With the arms in service position, lift one X1 wiper arm off the glass until it stays up and slide a folded towel underneath it. Never let a bare spring-loaded arm snap back onto the windshield.

🔧 Mechanic's note — Ray Delgado

I slide the towel under before lifting — with the arm parked upright in service position, I've learned it wants to fall sideways, and the towel is my insurance.

3

Release the old blade

The X1 F48 uses a top-lock (C1-type) connector: press the release tab on the blade connector and slide the blade off the arm. Pull straight along the arm and never twist sideways.

4

Match the new blade

The 2016-2022 X1 xDrive28i takes a 26-inch driver-side blade and a 16-inch passenger-side blade with the top-lock connector, plus a 13- to 14-inch rear blade (catalogs vary — measure the old one). Buy blades listed for the F48 X1 specifically, since the top-lock adapter differs from generic hook blades. Compare each new blade against the old one to verify the length.

5

Install until it clicks

Slide the new blade onto the arm until the top-lock clicks into place, then tug gently to confirm it is locked. The 26-inch blade goes on the driver side, the 16-inch on the passenger side.

6

Lower and repeat

Lower each arm gently onto the glass and repeat on the other side, then fit the rear blade. The sweep should be silent and streak-free.

🔧 Mechanic's note — Tom Becker

I listen to the sweep after lowering — on the X1 a chattering wipe usually means the blade isn't seated squarely, and I've fixed it by reseating rather than replacing.

All Done!

Test your repair before closing everything up. If something doesn't work right, double-check your steps.

⚠️ Common Mistakes to Avoid

  • • Forgetting to replace both wiper blades simultaneously
  • • Installing the wrong size wiper blades
  • • Not properly securing the wiper blades after installation