Quick answer: Spark Plug Replacement on a 2020–2024 BMW X3 M is rated Advanced and takes about 1.5 to 2 hours — the brace and rear cowl teardown plus cylinder 6 access take the time. You'll need 6 tools for this job, and parts cost about $115. This guide walks you through the full job step by step, including the mistakes to avoid.
| Part Name |
Part Number |
Price |
Buy |
| Correct spark plug set for the gasoline/ICE engine in 2020-2024 BMW X3 M; verify engine, heat range, gap, and VIN fitment |
— |
$115.00 |
|
| Coil-boot seals or ignition coils only if inspection finds damage Optional |
— |
$35.00 |
|
About prices: shown prices are typical retail averages and change frequently; cheaper alternatives may be available. Confirm the current price before buying.
💡 Pro tip: Order all parts at once to save on shipping
Step-by-Step Instructions
Follow these steps carefully
1
Confirm the S58 and disconnect the battery before touching the HPFP area
Park on level ground, set the parking brake, and let the engine cool completely. Disconnect the negative battery terminal before disturbing anything on top of the engine, particularly the high-pressure fuel pump connections that sit near the coil rail.
2
Remove the strut braces, cowl trim, and engine cover
Remove the plastic engine cover, then deal with the rear of the bay: the side plastic covers and the foam-like cowl piece at the back of the engine bay come off to expose cylinder 6, which otherwise hides underneath them.
🔧 Mechanic's note — Ray Delgado
The washer or taper seat must match. I verify — mismatched seats don't seal and damage heads. I don't drop plugs. A dropped plug can close the gap invisibly — I check gap if one falls.
3
Unplug and pull the six press-fit coil packs in order
Work front to back and keep all six coils in cylinder order on a clean rag. Squeeze the release tab on each coil's electrical connector and unplug it, then pull the coil straight up with a firm wiggle — the S58 coils are press-fit with no retaining bolts, and they can be snug after years of heat cycles. They do not sit flush with the head even when fully seated, so do not expect a bolted-down look. Cylinder 6 at the firewall is the hardest pull; a patient wiggle beats yanking, which can tear the coil boot. Inspect each boot for cracks or carbon tracking as it comes out.
4
Extract the plugs with a thin-wall 14mm 12-point socket
Break each plug loose counterclockwise and spin it out; a magnetic pickup tool retrieves any plug the socket does not grip. Note each old plug's condition in cylinder order.
5
Check the gap against the manual and hand-thread the new plugs
Thread each new plug into the head by hand for several full turns until finger-tight — lower the plug on the socket but start the threads with your fingertips on the extension so you can feel any binding.
6
Seat the plugs and press the coils firmly home
Push each coil firmly back onto its plug with a slight twist until it seats, then reconnect each electrical connector until the locking tab clicks — give each one a tug to confirm it is latched, since a half-seated connector causes a misfire.
7
Reinstall the cowl trim, braces, and cover, then verify
Refit the rear foam cowl piece and side plastic covers, reinstall the strut braces with their bolts tightened evenly, and press the engine cover back onto its posts. Reconnect the negative battery terminal. Start the engine and let it idle — it should be smooth with no check-engine light. If it misfires, a coil connector that is not fully clicked home is the usual suspect; shut down and reseat each one. Take a short test drive, watching for smooth boost delivery and no warning lights, then confirm no misfire codes have returned.
All Done!
Test your repair before closing everything up. If something doesn't work right, double-check your steps.
⚠️ Common Mistakes to Avoid
- • Using a standard deep socket that is too fat for the S58's narrow plug wells
- • Skipping the rear cowl-trim and foam removal and fighting cylinder 6 blind
- • Greasing or oiling the new plug threads, which changes the seating feel
- • Not fully latching a coil connector, causing a post-job misfire