EZCarFix DIY Auto Repair
← Back to BMW X3 M Guides

2020–2024 BMW X3 M

2020-2024 BMW X3 M — Engine Oil & Filter Change

By Ray Delgado ✓ Certified Mechanic · Published Sep 21, 2026 · Updated Oct 22, 2026

🔧🔧 Moderate 30-60 minutes $57 DIY

Save $63 by doing it yourself! Shop cost: $120

Quick answer: Engine Oil & Filter Change on a 2020–2024 BMW X3 M is rated Moderate and takes about 30-60 minutes. You'll need 2 tools for this job, and parts cost about $57. This guide walks you through the full job step by step, including the mistakes to avoid.

Quick Video Tutorial

Parts You Need

Total Cost
$57.00
Oil spec 3.0L inline-6 twin-turbo
Capacity 7.4 qt with filter Viscosity 0W-30 (alt: 0W-40, 5W-30, 5W-40) Spec BMW LL-04
Part Name Part Number Price Buy
Engine Oil (0W-30) — $45.00
Correct engine oil filter and drain-plug washer for 2020-2024 BMW X3 M — $12.00

About prices: shown prices are typical retail averages and change frequently; cheaper alternatives may be available. Confirm the current price before buying.

💡 Pro tip: Order all parts at once to save on shipping

Step-by-Step Instructions

Follow these steps carefully

1

Confirm oil specification and make the vehicle safe

The X3 M's S58 takes 7.0 liters (7.4 US quarts) of 5W-30 or 0W-30 meeting BMW Longlife-04. Buy an S58-specific kit (cartridge, O-ring, drain-plug seal) — no generic filter. The S58 has NO dipstick; check the level electronically through iDrive.

🔧 Mechanic's note — Tom Becker

I always buy the S58-specific kit — cartridge, O-ring, drain-plug seal — because the generic filter doesn't fit this housing. And with no dipstick, I plan my level check through iDrive before I start.

2

Warm briefly

Idle the engine for two to three minutes so the oil thins, then shut it off. Pop the hood and locate the cartridge filter housing - on the S58 the filter is serviced entirely from above.

3

Drain the oil and remove the old filter

Reinstall the plug with a NEW crush seal every time - BMW specifies a fresh sealing ring, and reusing the old one causes seeps. Now lift out the drained filter housing from the top of the engine, pull the old element, and note its orientation. Fit the new element into the housing.

🔧 Mechanic's note — Tom Becker

I never reuse that crush seal — BMW specifies a fresh sealing ring every drain, and I've traced seeps on these housings back to a reused one. Fresh ring, clean pan, no comebacks for me.

4

Install the correct oil quantity

Set your funnel in the filler neck and pour in 6.5 liters of the Longlife-04 oil to start. Wait a full minute for it to settle, then add the final half liter to reach the 7.0-liter capacity.

🔧 Mechanic's note — Tom Becker

I pour 6.5 liters first, then wait a full minute before adding the final half liter — the S58's oil needs time to settle. I check the level electronically in iDrive rather than guessing.

5

Check level, leaks, and service reminder

Start the engine and idle for one to two minutes, watching the oil-pressure warning go out. Park on level ground, keep the engine running, and read the oil level through iDrive. It should show at or near maximum, never over.

All Done!

Test your repair before closing everything up. If something doesn't work right, double-check your steps.

⚠️ Common Mistakes to Avoid

  • • Using the wrong viscosity, capacity, or filter
  • • Working under a vehicle supported only by a jack
  • • Reusing a crushed drain-plug washer or leaving the old filter gasket stuck
  • • Over-tightening the filter or drain plug
  • • Starting the engine without first verifying oil was added