Quick answer: Brake Pad Replacement on a 2023–2026 Chevrolet Corvette Z06 is rated Advanced and takes about 1-3 hours. You'll need 4 tools for this job, and parts cost about $205. This guide walks you through the full job step by step, including the mistakes to avoid.
| Part Name |
Part Number |
Price |
Buy |
| Front or rear brake pad set for 2023-2026 Chevrolet Corvette Z06; verify axle, brake package, and VIN fitment |
— |
$180.00 |
|
| Replacement pad hardware or wear sensor only if the kit requires it |
— |
$25.00 |
|
| Anti-seize compound |
— |
— |
|
About prices: shown prices are typical retail averages and change frequently; cheaper alternatives may be available. Confirm the current price before buying.
💡 Pro tip: Order all parts at once to save on shipping
Step-by-Step Instructions
Follow these steps carefully
1
Confirm axle, parts, and brake condition
Z06 front: fixed Brembo 6-piston calipers. Confirm rotors — iron takes pads; carbon-ceramic (CCB) uses different pads with electronic wear sensors, and CCB rotors must never be machined. Z06 pads aren't glued in — swap them without removing the calipers.
🔧 Mechanic's note — Tom Becker
I confirm iron versus carbon-ceramic before ordering anything. CCB pads, sensors, and handling are different — and CCB rotors never get machined. Mixing them up is an expensive mistake.
2
Lift and secure the vehicle
Park level, set the brake, chock the rear wheels. Lift the front at lift points with a jack onto stands — never under a jack-only car. Break the lug nuts loose, remove the wheel. Siphon the reservoir down from MAX.
3
Remove the caliper and old pads
With the caliper still bolted to the knuckle, remove the bridge pin bolt across the top of the caliper (a standard hex head, roughly 1/2"). Punch the two pad retaining pins out from the tapered end with a drift, then lift out the pad retaining spring. Note the location of the pad wear sensor before disturbing anything. Slide the old pads straight out through the top of the caliper. If a pad is stuck, wiggle it free - don't pry against the rotor face or the caliper bores.
4
Install pads and hardware
Compress all six pistons back into their bores evenly using a proper brake spreader tool, working around the pistons so none cocks sideways, and watch the reservoir level as fluid returns. Inspect the dust boots for heat damage and the pins and spring for corrosion - replace tired hardware. Apply a tiny amount of anti-seize (about 0.1 gram) to each end of the new pads' abutments where they contact the caliper, keeping it completely off the friction surfaces, per GM's procedure. Slide the new pads in, noting the wear-sensor position.
5
Torque, pump, and bed in
Reinstall the bridge pin through the pads, thread its bolt in by hand, and torque it to 30 N·m (22 lb ft) per GM's service procedure. Refit the pad retaining spring and the two retaining pins. Reinstall the wheel and torque the lug nuts in a star pattern to GM's specification (verify in your owner's manual). Pump the brake pedal until firm - do not drive until the pedal is solid. Bed the pads on a safe stretch of road: about six hard (but not ABS) stops from 60 mph down to 20, then drive 10 minutes with minimal braking to cool everything evenly.
All Done!
Test your repair before closing everything up. If something doesn't work right, double-check your steps.
⚠️ Common Mistakes to Avoid
- • Changing only one pad or mixing pad sets on an axle
- • Working under a vehicle supported only by a jack
- • Letting the caliper hang from the brake hose
- • Forcing a seized piston or ignoring a leaking caliper
- • Skipping final lug and caliper torque or the bedding procedure