EZCarFix DIY Auto Repair
← Back to Lexus ES Guides

2013–2018 Lexus ES

2013-2018 Lexus ES350 - Engine Mount Replacement DIY

By Ray Delgado ✓ Certified Mechanic · Published Sep 21, 2026 · Updated Oct 22, 2026

🔧🔧🔧 Advanced 2-3 hours $115 DIY 2 views

Save $510 by doing it yourself! Shop cost: $625

Quick answer: Engine Mount Replacement DIY on a 2013–2018 Lexus ES is rated Advanced and takes about 2-3 hours. You'll need 10 tools for this job, and parts cost about $115. This guide walks you through the full job step by step, including the mistakes to avoid.

Quick Video Tutorial

Parts You Need

Total Cost
$114.90
Part Name Part Number Price Buy
Front Engine Mount Optional MTA73437 $79.95
Front Passenger Side Engine Mount — $59.95
Left Transmission Mount MTA33230 $54.95
Right Transmission Mount Optional MTA33094 $54.95
Front Right Engine Mount Optional MTA40494 $64.95

About prices: shown prices are typical retail averages and change frequently; cheaper alternatives may be available. Confirm the current price before buying.

💡 Pro tip: Order all parts at once to save on shipping

Step-by-Step Instructions

Follow these steps carefully

1

Support the engine and disconnect the battery

Park the 2013-2018 Lexus ES350 on level ground, set the parking brake, and disconnect the negative battery cable. Support the engine from above with an engine support bar or from below with a jack and a wood block under the oil pan — never leave the engine hanging on remaining mounts alone. Wear gloves and eye protection.

🔧 Mechanic's note — Ray Delgado

I disconnect the ES350 negative cable and tuck it behind the fuse box — engine-mount work means the engine moves on the jack, and a cable that was clear at the start can end up touching the post by the end. I secure it.

2

Locate the failed mount and remove nearby covers

Identify which mount is bad (oil-soaked rubber, cracked insulator, or metal-to-metal contact) on the 2013-2018 Lexus ES350. Remove any engine covers, air boxes, or undertrays blocking access to that mount’s fasteners.

3

Unbolt the mount from the engine and chassis

Remove the through-bolt or nuts securing the mount to the engine bracket, then the fasteners into the frame/subframe. Note any ground straps, heat shields, or alignment dowels. Lower or raise the engine slightly only as needed for clearance — do not force the mount.

4

Compare and install the new mount

Seat it fully on the 2013-2018 Lexus ES350, install fasteners finger-tight first, then torque to the specified values once the engine is back at rest height.

🔧 Mechanic's note — Tom Becker

I verify stud pattern, snubber orientation, and hardness marks on the new ES350 mount against the old one at the bench. An incorrect mount changes engine geometry just enough to shake the whole car at idle.

5

Remove the support and check clearances

Remove the engine support bar/jack. Confirm the 2013-2018 Lexus ES350 mount is not twisted and that hoses, belts, and wiring have clearance. Reinstall covers and reconnect the battery.

6

Idle and road-test for vibration

Start the 2013-2018 Lexus ES350 and check for clunks or excessive movement in gear (auto: Park-to-Drive; manual: clutch engage). Road-test for vibration under acceleration and braking. Recheck mount torque after a short heat cycle if specified.

🔧 Mechanic's note — Tom Becker

I idle the ES350 and drive it after the mount — I feel for the smooth idle this car is famous for and listen for clunks over speed bumps. A bad mount turns a Lexus into a paint shaker, and I refuse to deliver that.

All Done!

Test your repair before closing everything up. If something doesn't work right, double-check your steps.

⚠️ Common Mistakes to Avoid

  • • Not properly supporting the engine before removing mounts, leading to potential engine damage.
  • • Using incorrect torque specifications when tightening new mounts, which can result in premature failure.
  • • Failing to inspect and replace other worn mounts, which can cause vibrations and affect vehicle performance.