EZCarFix DIY Auto Repair
← Back to BMW 4 Series Guides

2021–2024 BMW 4 Series

2021-2024 BMW 4 Series — Spark Plug Replacement

By Ray Delgado ✓ Certified Mechanic · Published Sep 21, 2026 · Updated Oct 19, 2026

🔧🔧🔧 Advanced 1–2 hours $115 DIY

Save $335 by doing it yourself! Shop cost: $450

Quick answer: Spark Plug Replacement on a 2021–2024 BMW 4 Series is rated Advanced and takes about 1–2 hours. You'll need 5 tools for this job, and parts cost about $115. This guide walks you through the full job step by step, including the mistakes to avoid.

Quick Video Tutorial

Parts You Need

Total Cost
$115.00
Part Name Part Number Price Buy
Correct spark plug set for the gasoline/ICE engine in 2021-2024 BMW 4 Series; verify engine, heat range, gap, and VIN fitment — $115.00
Coil-boot seals or ignition coils only if inspection finds damage Optional — $35.00

About prices: shown prices are typical retail averages and change frequently; cheaper alternatives may be available. Confirm the current price before buying.

💡 Pro tip: Order all parts at once to save on shipping

Step-by-Step Instructions

Follow these steps carefully

1

Prep — count your plugs: four or six

430i (2.0L turbo B46): four plugs; M440i (3.0L turbo B58): six, same as M4's S58. Coils sit under the big black engine cover in a straight row. Work on a cold engine and disconnect the negative battery terminal.

2

Access — cover off; B58 rear plug may need cowl trim removed

Pull the engine cover straight up off its rubber grommets. For the B58's rearmost plug tight against the firewall, remove the plastic cowl covers and unbolt the two metal strut braces for a straight shot. Keep fasteners in a tray.

3

Coil pack removal — slide the lock, unplug, unbolt

Slide the connector lock up or back; pull the connector off by its base, never the wires. Remove the hold-down bolt and pull the coil up, wiggling to break the boot's grip. Lay coils out in cylinder order.

4

Plug removal — 14mm 12-point thin-wall socket

Blow each well clean with compressed air first. Both engines use 14mm 12-point plugs in narrow tubes — use a thin-wall socket, since a thick-wall socket jams. Spin each plug out by hand with a long extension.

🔧 Mechanic's note — Ray Delgado

Before you toss the old plugs, lay them side by side. On these turbo engines, one sooty or oil-wet plug among clean ones usually means a failing coil or injector in that cylinder — I catch a lot of misfires that way.

5

Install new plugs — gap per the manual, hand-thread only at first

Gap new plugs to the manual or underhood sticker — never touch the fine center electrode. Plugs install dry. Start each by hand (aluminum cross-threads easily), then tighten to spec; over-tightening cracks the plug or strips the head.

6

Reassembly — coils, connectors, braces, and cover

Press each coil down, snug its hold-down bolt, and reconnect every connector — slide each lock home and tug to confirm. Reinstall cowl covers and braces, seat the engine cover on its grommets, and reconnect the battery.

🔧 Mechanic's note — Ray Delgado

I put a thin smear of dielectric grease inside each coil boot before I press them down. It makes the next plug change far easier — these boots bond to the porcelain over 60,000 miles and tear otherwise.

7

Verification — start, idle check, and interval note

Start the engine — confirm a smooth idle with no warning lights. A short gentle drive should show no stumble under boost. A misfire code right after the job almost always means a coil connector's sliding lock isn't fully engaged.

🔧 Mechanic's note — Ray Delgado

BMW's condition-based service calls for fresh plugs around 60,000 miles on these turbo engines — I do them sooner if the car is tuned or driven hard. A misfire code right after the job almost always means a coil connector's sliding lock isn't fully engaged.

All Done!

Test your repair before closing everything up. If something doesn't work right, double-check your steps.

⚠️ Common Mistakes to Avoid

  • • Using a standard thick-wall 14mm socket that jams in the narrow plug tubes instead of a thin-wall 12-point socket.
  • • Forgetting to re-engage the sliding lock on a BMW coil connector, causing an intermittent misfire.
  • • Skipping removal of the cowl trim and strut braces on the B58, then fighting the rearmost plug at an angle.