EZCarFix DIY Auto Repair
← Back to BMW 4 Series Guides

2014–2020 BMW 4 Series

2014-2020 BMW 4 Series — Engine Oil & Filter Change

By Ray Delgado ✓ Certified Mechanic · Published Sep 21, 2026 · Updated Nov 7, 2026

🔧🔧 Moderate 30-60 minutes $57 DIY

Save $63 by doing it yourself! Shop cost: $120

Quick answer: Engine Oil & Filter Change on a 2014–2020 BMW 4 Series is rated Moderate and takes about 30-60 minutes. You'll need 3 tools for this job, and parts cost about $57. This guide walks you through the full job step by step, including the mistakes to avoid.

Quick Video Tutorial

Parts You Need

Total Cost
$57.00
Oil spec 2.0L turbo I4
Capacity 5.3 qt with filter Viscosity 0W-20 (alt: 5W-30)
Part Name Part Number Price Buy
Engine Oil (0W-20) — $45.00
Correct engine oil filter and drain-plug washer for 2014-2020 BMW 4 Series — $12.00
Replacement plastic drain plug (RWD N20 only) — —

About prices: shown prices are typical retail averages and change frequently; cheaper alternatives may be available. Confirm the current price before buying.

💡 Pro tip: Order all parts at once to save on shipping

Step-by-Step Instructions

Follow these steps carefully

1

Confirm oil specification and make the vehicle safe

Three engines, three fills. 428i N20: 5.0L (RWD) / 5.5L (xDrive) 5W-30 LL-01. 430i B46: 5.5 qt 0W-20. 440i B58: 6.5L 0W-20. All use top-mounted cartridge. RWD N20: PLASTIC drain plug — buy new one. Park level, brake set, chocked.

🔧 Mechanic's note — Tom Becker

Three engines, three fills — I confirm which one I'm working on before buying oil. The wrong jug on these cars is an expensive mistake, and I've learned to check the badges and the bay first.

2

Warm briefly and protect the work area

Warm engine just enough for oil to flow. Remove fill cap; drain pan under sump. Remove underbody panels. RWD N20: new plastic plug ready. 27mm socket opens top-mounted housing — on N20 sits top at front. Let housing drain first.

3

Drain the used oil and replace the filter

Drain fully. RWD N20: NEW plastic plug — don't reuse old one. xDrive and B46/B58: metal plug, new seal, 18 ft-lbs. From above, open housing with 27mm socket; swap element and O-rings, lightly oiled. Clean spilled oil from valley.

🔧 Mechanic's note — Tom Becker

On the RWD N20 I buy a new plastic drain plug every time — that one is single-use. Reusing it is how I've seen a weeping plug turn into a pan rethread nobody wants to pay for.

4

Install the correct oil quantity

Add most of the specified amount — don't pour the last bit blindly. No dipstick: run briefly, check the electronic level in iDrive, top up in small increments to the max. Keep the fill cap area clean; refit tightly.

5

Check level, leaks, and service reminder

Idle; inspect the plug and housing for leaks. Take a short drive, recheck the level in iDrive. Reset the service reminder; record the mileage and oil grade. On B46/B58, confirm the new interval displays first.

All Done!

Test your repair before closing everything up. If something doesn't work right, double-check your steps.

⚠️ Common Mistakes to Avoid

  • • Using the wrong viscosity, capacity, or filter
  • • Working under a vehicle supported only by a jack
  • • Reusing a crushed drain-plug washer or leaving the old filter gasket stuck
  • • Over-tightening the filter or drain plug
  • • Starting the engine without first verifying oil was added