EZCarFix DIY Auto Repair
← Back to BMW 7 Series Guides

2009–2015 BMW 7 Series

2009-2015 BMW 750i — Oil and Filter Change

By Tom Becker ✓ Certified Mechanic · Published Sep 21, 2026 · Updated Oct 14, 2026

🔧🔧 Moderate 30-60 minutes $90 DIY

Save $30 by doing it yourself! Shop cost: $120

Quick answer: Oil and Filter Change on a 2009–2015 BMW 7 Series is rated Moderate and takes about 30-60 minutes. You'll need 2 tools for this job, and parts cost about $90. This guide walks you through the full job step by step, including the mistakes to avoid.

Quick Video Tutorial

Parts You Need

Total Cost
$90.00
Oil spec N63 4.4L twin-turbo V8 (2009-2015): 9.0 qt / N62 4.8L V8 (2007-2008 750i): 8.5 qt — same procedure
Capacity 9.0 qt with filter Viscosity 5W-30 (alt: 0W-30) Spec BMW Longlife-01
Part Name Part Number Price Buy
BMW Longlife-01 approved 5W-30 or 0W-30 engine oil (9.0 qt) — $56.00
N63 oil filter cartridge with O-ring — $32.00
Oil drain plug crush washer — $2.00

About prices: shown prices are typical retail averages and change frequently; cheaper alternatives may be available. Confirm the current price before buying.

💡 Pro tip: Order all parts at once to save on shipping

Step-by-Step Instructions

Follow these steps carefully

1

Warm the N63 engine and park on level ground

Idle the N63 twin-turbo V8 about 5 minutes so its large oil volume thins and drains fully, then switch off and set the parking brake. Park level — the F01's electronic oil-level check requires the car to sit flat.

2

Remove the V8 engine cover

Lift the large acoustic engine cover straight up off its mounts to expose the hot-vee top. The oil filter housing sits on top between the cylinder banks, easy to reach. Set the cover aside safely.

3

Replace the top-mounted oil filter cartridge

Fit a filter cap socket to the black plastic housing cap and loosen it slowly so trapped oil drains back into the housing. Lift the cap out with the cartridge attached, pull the old element off the stem, and remove the old O-ring from its groove. Lubricate the new O-ring with fresh oil, fit the new cartridge, and thread the cap back on to the BMW specification without forcing it.

4

Raise the car and drain the oil pan

Chock the wheels, raise the front at the factory jacking points, and rest the car on jack stands — never work under a jack alone. Slide a large drain pan under the oil pan, remove the drain plug, and let the oil drain until it slows to an occasional drip; the N63 holds roughly 8.5 liters, so give it time.

5

Reinstall the drain plug with a new crush washer

Fit a new crush washer to the plug — the old one won't seal twice — and start it by hand to avoid cross-threading. Tighten to the BMW specification; wipe the pan clean so future seepage is easy to spot.

6

Lower the car and refill with 5W-30

Lower the car to level ground and pour in approximately 8.5 liters of BMW Longlife-01 approved 5W-30, holding back the last liter. Add gradually — removing excess oil from a V8 sump is a chore.

🔧 Mechanic's note — Tom Becker

Hold back that last liter and check the gauge before adding it — sucking excess oil out of an N63 sump is a chore I only did once.

7

Verify the electronic oil level

Start the engine, let it reach operating temperature, then check the oil level in the cluster service menu. The electronic sensor needs a minute or two to measure — add small amounts until the gauge reads maximum, never above it.

8

Reset the service indicator and check for leaks

Reset the engine oil service item through the cluster service menu so the condition-based service counter restarts. Take a short drive, then recheck the drain plug and filter housing for any sign of leaks.

All Done!

Test your repair before closing everything up. If something doesn't work right, double-check your steps.

⚠️ Common Mistakes to Avoid

  • • Using the wrong viscosity, capacity, or filter
  • • Working under a vehicle supported only by a jack
  • • Reusing a crushed drain-plug washer or leaving the old filter gasket stuck
  • • Over-tightening the filter or drain plug
  • • Starting the engine without first verifying oil was added