← Back to BMW M2 Guides

2023–2026 BMW M2

2023-2026 BMW M2 — Spark Plug Replacement

By Ray Delgado ✓ Certified Mechanic · Published Sep 24, 2026 · Updated Oct 14, 2026

🔧🔧🔧 Advanced 1-2 hours $156 DIY

Save $188 by doing it yourself! Shop cost: $344

Quick answer: Spark Plug Replacement on a 2023–2026 BMW M2 is rated Advanced and takes about 1-2 hours. You'll need 5 tools for this job, and parts cost about $156. This guide walks you through the full job step by step, including the mistakes to avoid.

Quick Video Tutorial

Parts You Need

Total Cost
$156.00
Part Name Part Number Price Buy
6x OEM spark plugs for the S58 engine (G87 M2) — $142.00
6x ignition coil boots (replace if heat-cracked) — —
Dielectric grease — $14.00

About prices: shown prices are typical retail averages and change frequently; cheaper alternatives may be available. Confirm the current price before buying.

💡 Pro tip: Order all parts at once to save on shipping

Step-by-Step Instructions

Follow these steps carefully

1

Cool the engine and remove the engine cover

Let the S58 cool completely (overnight is ideal) and park the M2 on level ground. Pop the hood and release the clips to remove the plastic engine cover, exposing the six coil packs on the valve cover.

2

Disconnect the coil-pack connectors

Squeeze the locking tab on each coil-pack electrical connector and unplug all six. Work from one end of the engine to the other and keep the harness laid back out of the way.

3

Unbolt and remove the six coil packs

Remove the bolt securing each coil pack - a T30 Torx on the S58 - and pull the coils straight up out of their tubes. If a coil resists, twist gently rather than yanking; set them aside in cylinder order.

4

Blow out the plug tubes

Blow compressed air down each plug tube to clear out any grit. Anything left in the tube will drop straight into the combustion chamber when the plug comes out.

5

Remove the old spark plugs

Using a 14mm thin-wall magnetic spark plug socket on an extension, loosen each plug and lift it out. Inspect the old plugs for unusual fouling or damage as they come out.

6

Install the new plugs by hand first

Confirm the new plugs are the correct OEM S58 part and come pre-gapped; do not re-gap them. Lower each plug in on the magnetic socket, thread it by hand several turns to avoid cross-threading, then snug gently with the ratchet.

🔧 Mechanic's note — Tom Becker

I always thread plugs in by hand for several full turns before touching the ratchet. The S58 has an aluminum head, and one cross-threaded plug turns a Saturday job into a machine-shop bill.

7

Refit the coils and reconnect everything

Apply a light film of dielectric grease inside each coil boot, slide the coil packs back over the plugs, and reinstall their bolts. Reconnect all six electrical connectors until each one clicks positively into place.

8

Reassemble and verify under a test drive

Refit the engine cover, confirm no tools or rags are left in the bay, and close the hood. Start the engine; it should idle with no warning lights. A drive with moderate pulls confirms the plugs fire cleanly under boost.

All Done!

Test your repair before closing everything up. If something doesn't work right, double-check your steps.

⚠️ Common Mistakes to Avoid

  • • Using a standard thick-wall spark plug socket - the S58's plug tubes are tight and demand a thin-wall 14mm magnetic socket.
  • • Dropping a new plug into the tube, which can crack the ceramic insulator and cause a misfire under boost.
  • • Over-tightening plugs into the aluminum cylinder head instead of seating them by hand first and finishing gently.
  • • Forgetting to reconnect one of the six coil connectors, which produces an immediate misfire code on startup.
  • • Reusing coil boots that are heat-cracked instead of replacing them while everything is already apart.