EZCarFix DIY Auto Repair
← Back to Chevrolet Bolt EV Guides

2017–2023 Chevrolet Bolt EV

2017-2023 Chevrolet Bolt EV — Wiper Blade Replacement

By Ray Delgado ✓ Certified Mechanic · Published Sep 21, 2026 · Updated Oct 19, 2026

🔧 Easy 15–20 minutes for all three blades $81 DIY

Quick answer: Wiper Blade Replacement on a 2017–2023 Chevrolet Bolt EV is rated Easy and takes about 15–20 minutes for all three blades. You'll need 3 tools for this job, and parts cost about $81. This guide walks you through the full job step by step, including the mistakes to avoid.

Quick Video Tutorial

Parts You Need

Total Cost
$80.97
Part Name Part Number Price Buy
Driver wiper blade, 26" Bosch 26A $32.99
Passenger wiper blade, 26" Bosch 26B $32.99
Rear wiper blade, 12" — $14.99

About prices: shown prices are typical retail averages and change frequently; cheaper alternatives may be available. Confirm the current price before buying.

💡 Pro tip: Order all parts at once to save on shipping

Step-by-Step Instructions

Follow these steps carefully

1

Confirm the blade sizes — 26, 26, and about 12 inches

Both front blades are 26 inches (68 cm per the owner's manual). Buy push-button (top-lock, 22 mm) blades — hook-style blades won't fit. Rear: manual says 30 cm (sold as 12), some charts say 11; measure the old blade.

🔧 Mechanic's note — Tom Becker

I always check the connector box on the blade packaging before paying — universal blades often only ship with a J-hook, and the Bolt's arms won't take it. Push-button (top-lock) adapters, or walk away.

2

Park the car and pull the front arms away from the glass

Switch off — no service position needed. Lift each arm away from the glass, gripping near the hinge. Slide a folded towel under each arm: the manual warns a bare arm can damage the glass, and that damage isn't covered by the vehicle warranty.

3

Remove the old driver-side blade — press the center button

2018+: press the middle button on the arm connector and pull the blade off. 2017: flip open the cover, push the release lever, and push the arm out. Support the arm with your other hand; note the connector's orientation.

4

Install the new 26-inch driver-side blade

Push the new 26-inch blade onto the connector until the center button clicks into lock, then pull firmly — an unseated connector releases when the wipers reverse. On 2017 cars, snap the cover down afterward. Lower the arm gently, holding the arm itself.

5

Replace the 26-inch passenger-side blade

Repeat the same procedure on the passenger side: same 26-inch length, same push-button connector, same press-and-pull removal. Seat the new blade until it clicks and rest the arm on the glass.

6

Replace the rear wiper blade — remove its cover first

Pry off the rear cover with a trim tool. Press the release lever, slide out the old blade, and fit the new 12-inch blade (some charts say 11 — match your measurement) until it clicks. Refit the cover in the slot and snap it down.

🔧 Mechanic's note — Tom Becker

Charts say 11, the manual says 12 — always measure the old rear blade before buying; I trust the tape over the chart on this car.

7

Test the wipers and washers

Switch on and run the washers at low and high speed plus a rear cycle. New blades should clear without streaks, skipping, or chatter. If a front blade chatters, recheck its push-button connector is fully locked. Wipe edges with a damp cloth if they squeak.

All Done!

Test your repair before closing everything up. If something doesn't work right, double-check your steps.

⚠️ Common Mistakes to Avoid

  • • Buying J-hook blades for the Bolt — its arms use a push-button (22 mm top-lock) connector that a hook blade cannot attach to.
  • • Trying to pry the rear blade off without removing its protective cover first; the cover unsnaps upward with a plastic tool, then slides toward the blade tip.
  • • Assuming the rear blade is 12 inches without measuring — the owner's manual says 30 cm (11.8 in) but several charts list 11 inches, so match the old blade.
  • • Forgetting to snap the 2017 cars' blade covers back down after fitting the new front blades.