← Back to Chevrolet Uplander Guides

2005–2009 Chevrolet Uplander

2005-2009 Chevrolet Uplander — Cabin Air Filter Replacement

By Tom Becker ✓ Certified Mechanic · Published Sep 21, 2026 · Updated Oct 22, 2026

🔧 Easy 10–15 minutes $28 DIY

Save $72 by doing it yourself! Shop cost: $100

Quick answer: Cabin Air Filter Replacement on a 2005–2009 Chevrolet Uplander is rated Easy and takes about 10–15 minutes. No tools are required for this job, and parts cost about $28. This guide walks you through the full job step by step, including the mistakes to avoid.

Quick Video Tutorial

Parts You Need

Total Cost
$28.00
Part Name Part Number Price Buy
Cabin air filters (pair) for 2005-2009 Chevrolet Uplander; verify arrows, size, and VIN/trim fitment — $28.00

About prices: shown prices are typical retail averages and change frequently; cheaper alternatives may be available. Confirm the current price before buying.

💡 Pro tip: Order all parts at once to save on shipping

Step-by-Step Instructions

Follow these steps carefully

1

Open the glove box — this van takes TWO filters

2005–2009 Uplander takes TWO cabin filter elements side by side, inside the glove box behind a small access door. Open the passenger-side glove box and buy two elements, not one.

🔧 Mechanic's note — Tom Becker

Buy two filters, not one. Half the Uplander owners I meet are making a second trip to the parts store right now.

2

Find the removable panel on the left side of the glove box

On the glove box's left wall: a panel with a pull tab at its bottom — no screws, no tools. Pull the bottom tab outward to pop it free. If it resists, pull straight out from the tab — prying the top edge breaks it.

3

Open the filter access door to the right

Behind the removed panel sits the filter access door. Pull out on its left-hand latch and swing the door open to the right. Photograph how the two filters sit before pulling them — they stack in a specific order and orientation.

4

Slide out both old filters and note their order

Pull both elements out, noting which came first and each orientation — replacements go back the same way. The correct pair fills the compartment with no gaps. Old ones are gray and matted; a never-changed pair is startlingly dirty and explains weak A/C airflow.

🔧 Mechanic's note — Ray Delgado

I've learned: Note which filter came out first and how each sat — the pair stacks in a defined order, and guessing gets you a crooked install.

5

Clean the compartment and check the door seal

With both filters out, pick dust and debris by hand — don't push anything toward the blower. Wipe the door and its edges with a cloth. Check the latch springs positively; a latch that won't catch leaves the door ajar, letting unfiltered air in.

6

Install the two new filters and close the door

Slide the two filters in matching the old order and orientation — fully home, flat, no gaps. Swing the access door left until the latch catches and tug to confirm it's locked. Press the glove box panel back into the left wall until flush.

🔧 Mechanic's note — Tom Becker

I never trust my eyes alone here: Tug that access door after it latches. A door left ajar leaks dusty air past both filters, which defeats the whole job.

7

Run the blower and confirm the job

Start the van, run the blower low to max on fresh air: airflow at dash and rear vents, no glove-box rattle. Recheck yearly or every 12,000–15,000 miles — always two filters, never one.

All Done!

Test your repair before closing everything up. If something doesn't work right, double-check your steps.

⚠️ Common Mistakes to Avoid

  • • Buying only one filter — the Uplander takes TWO elements side by side, and a single-element box leaves the job half done.
  • • Pulling the removable panel from the top edge instead of the bottom tab, snapping the tab off.
  • • Mixing up the order or orientation of the two elements; photograph the old pair before removing them.
  • • Leaving the access door unlatched so it leaks unfiltered air and rattles behind the glove box.