EZCarFix DIY Auto Repair
← Back to Chevrolet Uplander Guides

2005–2009 Chevrolet Uplander

2005-2009 Chevrolet Uplander — Spark Plug Replacement

By Tom Becker ✓ Certified Mechanic · Published Sep 21, 2026 · Updated Oct 22, 2026

🔧🔧🔧 Advanced 1-3 hours $115 DIY

Save $335 by doing it yourself! Shop cost: $450

Quick answer: Spark Plug Replacement on a 2005–2009 Chevrolet Uplander is rated Advanced and takes about 1-3 hours. You'll need 4 tools for this job, and parts cost about $115. This guide walks you through the full job step by step, including the mistakes to avoid.

Quick Video Tutorial

Parts You Need

Total Cost
$115.00
Part Name Part Number Price Buy
Correct spark plug set for the gasoline/ICE engine in 2005-2009 Chevrolet Uplander; verify engine, heat range, gap, and VIN fitment — $115.00
Coil-boot seals or ignition coils only if inspection finds damage Optional — $35.00

About prices: shown prices are typical retail averages and change frequently; cheaper alternatives may be available. Confirm the current price before buying.

💡 Pro tip: Order all parts at once to save on shipping

Step-by-Step Instructions

Follow these steps carefully

1

Confirm engine and plug fitment

Uplander plugs depend on engine: 2005–2006 3.5L V6 uses AC Delco 41-902, gap 0.060"; 3.9L V6 (2006–2009): NGK IZTR4A11 or Denso IT16, gap 0.044". Buy six — mixing specs causes misfires.

2

Cool and expose the plugs

Let the V6 cool completely — aluminum heads strip when hot. Remove the engine cover: front coils are one bolt and one connector each. The rear coils sit against the firewall; remove wiper cowl or alternator bracket, or work by feel with wobble extensions.

🔧 Mechanic's note — Tom Becker

My shop rule on these: Do the rear bank by feel with wobble extensions, and give yourself the whole afternoon. Rushing the rear bank is how plugs get cross-threaded.

3

Remove coils and clean wells

Release each coil by its connector — pull the connector body, never the wiring — remove its bolt and lift it out, keeping cylinder order. Clear debris from each plug well first; grit falls into the cylinder. Inspect boots for cracks, oil, or white tracking.

🔧 Mechanic's note — Tom Becker

I tell every DIYer this: Keep the coils in cylinder order and check every boot for white tracking marks — a cracked boot misfires just like a bad plug.

4

Install the new plugs

Confirm new plugs match old reach and heat range — 3.5L and 3.9L plugs are not interchangeable. Start each by hand, turning backward a half-turn first; never force a binding plug. Torque to spec; no impact or anti-seize. Use a 5/8″ socket.

🔧 Mechanic's note — Ray Delgado

I've seen this go wrong too often: That backward half-turn seats the threads before they bite — on the blind rear bank it's the difference between a clean install and a stripped head.

5

Reconnect and verify

Seat each coil, refit its bolt, and click every connector home — check the rear three by feel. Refit ducting, cowl, and cover. Start: smooth idle, no check-engine light. Scan for P0300–P0306 after a test drive; stop if a thread bound or a code returns.

All Done!

Test your repair before closing everything up. If something doesn't work right, double-check your steps.

⚠️ Common Mistakes to Avoid

  • • Using the wrong plug or assuming a pre-gapped plug needs no verification
  • • Blowing debris into an open cylinder or plug well
  • • Cross-threading a plug or tightening it without a torque wrench
  • • Overusing anti-seize or dielectric grease on the plug threads
  • • Mixing coil connectors or ignoring a misfire after reassembly