EZCarFix DIY Auto Repair
← Back to Buick Regal Guides

2017–2022 Buick Regal

2017-2022 Buick Regal Sportback - Replace Tie Rod End

By Ray Delgado ✓ Certified Mechanic · Published Sep 21, 2026 · Updated Oct 22, 2026

🔧🔧🔧 Advanced 2-3 hours $53 DIY

Save $347 by doing it yourself! Shop cost: $400

Quick answer: Replace Tie Rod End on a 2017–2022 Buick Regal is rated Advanced and takes about 2-3 hours. You'll need 8 tools for this job, and parts cost about $53. This guide walks you through the full job step by step, including the mistakes to avoid.

Quick Video Tutorial

Parts You Need

Total Cost
$52.93
Part Name Part Number Price Buy
Outer Tie Rod End X37TE7414 $32.93
Tie Rod End Boot — $15.00
Tie Rod End Nut — $5.00
Cotter pin — —

About prices: shown prices are typical retail averages and change frequently; cheaper alternatives may be available. Confirm the current price before buying.

💡 Pro tip: Order all parts at once to save on shipping

Step-by-Step Instructions

Follow these steps carefully

1

Raise the vehicle

The outer tie rod end links the steering rack to the knuckle and sets your front toe — on the 2017-2022 Buick Regal Sportback it is a wear item worth confirming before you replace it. With the front end safely supported on stands, rock the tire at 3 and 9 o'clock: play or a dull clunk at the outer joint, a torn ball-joint boot, or inner-edge tire feathering all point to the end. Note that the Regal Sportback is the liftback variant on the E2XX platform — order the tie rod end for the Sportback specifically, since steering parts can differ from the related TourX wagon. A worn end typically causes highway-speed shimmy and vague on-center steering.

2

Mark the tie rod for length reference

Loosen the lug nuts on level ground, raise the Buick Regal, and support it on jack stands at the pinch welds or subframe.

3

Separate the outer tie rod from the knuckle

Break the jam nut loose on the inner rod while holding the inner rod steady with a second wrench — letting it twist disturbs the rack boot and your thread reference.

🔧 Mechanic's note — Tom Becker

I hold the inner rod steady with a second wrench — I've let it twist before and disturbed the rack boot, which turned a tie rod into a boot job too.

4

Thread the new end on to the paint mark

Thread the new end on for exactly the same number of turns, stopping at your paint mark. Be precise — a single turn changes toe measurably — but remember this only approximates the setting. Insert the new end into the knuckle and install the castle nut.

5

Fit a new cotter pin and check the boot

Install a new cotter pin through the castle nut where applicable; never reuse a stretched pin. Confirm the ball-joint boot sits evenly with no twist, and wipe off any excess grease.

🔧 Mechanic's note — Ray Delgado

I always use a new cotter pin — I've seen a reused stretched pin work loose, and the castle nut backing off is not something you want to discover.

6

Lower and get a toe alignment

Reinstall the wheel, torque the lug nuts in a star pattern, and lower the Buick Regal. Some pull is normal until the alignment is done. Drive directly to a shop for a toe alignment — don't postpone it; bad toe feathers tires quickly and can cause darting under braking.

All Done!

Test your repair before closing everything up. If something doesn't work right, double-check your steps.

⚠️ Common Mistakes to Avoid

  • • Not properly securing the vehicle with jack stands before starting the repair.
  • • Failing to measure the length of the old tie rod end before installation, leading to alignment issues.
  • • Using excessive force when separating the tie rod end from the steering knuckle, potentially damaging components.