EZCarFix DIY Auto Repair
← Back to Chevrolet Spark Guides

2016–2022 Chevrolet Spark

2016-2022 Chevrolet Spark — Spark Plug Replacement

By Ray Delgado ✓ Certified Mechanic · Published Sep 21, 2026 · Updated Oct 22, 2026

🔧🔧🔧 Advanced 1-3 hours $150 DIY

Save $300 by doing it yourself! Shop cost: $450

Quick answer: Spark Plug Replacement on a 2016–2022 Chevrolet Spark is rated Advanced and takes about 1-3 hours. You'll need 4 tools for this job, and parts cost about $150. This guide walks you through the full job step by step, including the mistakes to avoid.

Quick Video Tutorial

Parts You Need

Total Cost
$150.00
Part Name Part Number Price Buy
Correct spark plug set for the gasoline/ICE engine in 2016-2022 Chevrolet Spark; verify engine, heat range, gap, and VIN fitment — $115.00
Coil-boot seals or ignition coils only if inspection finds damage — $35.00

About prices: shown prices are typical retail averages and change frequently; cheaper alternatives may be available. Confirm the current price before buying.

💡 Pro tip: Order all parts at once to save on shipping

Step-by-Step Instructions

Follow these steps carefully

1

Confirm engine and plug fitment

Verify the part number against your VIN before ordering, and scan for misfire codes (P0300-P0304) so you know whether you are chasing a specific cylinder.

2

Cool and expose the plugs

Let the engine cool completely — pulling plugs from a hot aluminum head risks thread damage. Pop off the plastic engine cover to expose the four coil packs sitting on top of the valve cover. Each coil has a 4-pin electrical connector and a single mounting bolt. Disconnect the negative battery cable as a precaution, then release each coil connector by pressing its locking tab. Remove the coil hold-down bolts (10mm) and lift each coil straight up; keep the coils in order so each one goes back on its original cylinder.

🔧 Mechanic's note — Ray Delgado

I look at the porcelain for cracks before installing. A cracked plug misfires from day one. The plug threads should turn smoothly by hand. Any binding means stop and investigate.

3

Inspect the wells and coil boots

Check each well for oil: a wet well means the valve-cover gasket tube seals are leaking, and new plugs alone will not fix the misfire. Inspect each coil boot for cracks, carbon tracking, or a stretched spring while they are out.

4

Remove and install plugs

Break each old plug loose, then spin it out by hand. Thread each new iridium plug in by hand several full turns to avoid cross-threading the aluminum head, then torque to the manufacturer's specification — never use an impact for final seating.

5

Reconnect and verify

Apply only a light film of dielectric grease to the inside of each coil boot (never on the plug electrodes or threads), then press each coil firmly onto its plug until it seats and reinstall the hold-down bolts. Reconnect all four coil connectors until they click, refit the engine cover, and reconnect the battery. Start the Spark and let it idle — it should be smooth within a few seconds. Clear any stored misfire codes and take a short drive with a few steady-throttle pulls; if a misfire code returns on one cylinder, swap that coil to another cylinder and see if the code follows it.

All Done!

Test your repair before closing everything up. If something doesn't work right, double-check your steps.

⚠️ Common Mistakes to Avoid

  • • Using the wrong plug or assuming a pre-gapped plug needs no verification
  • • Blowing debris into an open cylinder or plug well
  • • Cross-threading a plug or tightening it without a torque wrench
  • • Overusing anti-seize or dielectric grease on the plug threads
  • • Mixing coil connectors or ignoring a misfire after reassembly