EZCarFix DIY Auto Repair
← Back to Chevrolet Spark Guides

2016–2022 Chevrolet Spark

2016-2022 Chevrolet Spark — Engine Air Filter Replacement

By Tom Becker ✓ Certified Mechanic · Published Sep 21, 2026 · Updated Oct 22, 2026

🔧 Easy 10-15 minutes $35 DIY

Save $75 by doing it yourself! Shop cost: $110

Quick answer: Engine Air Filter Replacement on a 2016–2022 Chevrolet Spark is rated Easy and takes about 10-15 minutes. You'll need 1 tool for this job, and parts cost about $35. This guide walks you through the full job step by step, including the mistakes to avoid.

Quick Video Tutorial

Parts You Need

Total Cost
$35.00
Part Name Part Number Price Buy
Engine air filter for 2016-2022 Chevrolet Spark; verify engine, housing shape, and VIN fitment — $35.00

About prices: shown prices are typical retail averages and change frequently; cheaper alternatives may be available. Confirm the current price before buying.

💡 Pro tip: Order all parts at once to save on shipping

Step-by-Step Instructions

Follow these steps carefully

1

Find the airbox on the passenger side of the bay

Park on level ground, shut the engine off, let it cool, and pop the hood. Make sure the housing and the components around it are free of dirt and debris before you open it, or that grit falls straight into the intake.

2

Remove the two cover screws

That's all that holds the Spark's air cleaner cover on: two screws, no clips, no clamps, no hoses to disconnect. Don't force them; they thread into plastic and the heads chew easily with the wrong driver.

🔧 Mechanic's note — Tom Becker

The old filter's condition guides my interval. If it's filthy, I shorten the replacement cycle. OEM filters fit better than cheap aftermarket. I've fought enough ill-fitting filters to pay the difference.

3

Lift the cover straight out of the assembly

With the screws out, lift the cover straight up and out of the assembly in one piece. If it sticks, wiggle it straight up rather than prying sideways against the housing lip, which can crack the plastic edge. Set the cover face-up somewhere clean — setting it face-down in dirt just re-contaminates the sealing surface you're about to close over a fresh filter.

4

Pull the old filter and inspect it in daylight

Lift the old element out and hold it up to daylight: if you can't see light through the pleats, or the media is torn, oily, or deformed, it's done.

5

Wipe the housing

If it sits crooked, the cover won't close right and unfiltered air sneaks past the seal. Wipe any dirt, leaves, and grit out of the empty housing with a clean rag before the new filter goes in.

6

Lower the cover and run the two screws back in

These screws thread into plastic, and overtightening strips the threads, after which the cover never seals properly again. Press down on the cover as you run the screws in so it seats square on the filter.

7

Verify, and respect the air-cleaner-off warning

Start the engine and confirm a smooth idle with no whistle at the box and no check-engine light. Never operate the engine with the air cleaner removed — the manual warns you can be burned, because the air cleaner also stops a backfire flame from reaching you. Check the element at each oil change and replace it per the maintenance schedule in your owner's manual; dusty roads shorten its life fast.

All Done!

Test your repair before closing everything up. If something doesn't work right, double-check your steps.

⚠️ Common Mistakes to Avoid

  • • Blowing the old filter out with compressed air or washing it with water — the owner's manual specifically forbids both; a damaged element lets dirt straight through.
  • • Stripping the two cover screws by overtightening — they thread into plastic; snug is enough.
  • • Shaking the dusty old filter off over the open housing — tap it away from the vehicle so dust doesn't fall into the clean side of the box.
  • • Setting the new filter in crooked — it must sit flat all around or the cover won't seal and unfiltered air gets past.