EZCarFix DIY Auto Repair
← Back to Dodge Intrepid Guides

1998–2004 Dodge Intrepid

1998-2004 Dodge Intrepid — Front Brake Pad Replacement

By Ray Delgado ✓ Certified Mechanic · Published Sep 24, 2026 · Updated Oct 14, 2026

🔧🔧 Moderate 60-90 minutes $71 DIY

Save $294 by doing it yourself! Shop cost: $365

Quick answer: Front Brake Pad Replacement on a 1998–2004 Dodge Intrepid is rated Moderate and takes about 60-90 minutes. You'll need 6 tools for this job, and parts cost about $71. This guide walks you through the full job step by step, including the mistakes to avoid.

Quick Video Tutorial

Parts You Need

Total Cost
$71.00
Part Name Part Number Price Buy
Front ceramic brake pad set (1998-2004 Intrepid) — $52.00
Brake cleaner spray — $10.00
High-temperature silicone brake grease — $9.00
Replacement caliper pin boots (if torn) Optional — —

About prices: shown prices are typical retail averages and change frequently; cheaper alternatives may be available. Confirm the current price before buying.

💡 Pro tip: Order all parts at once to save on shipping

Step-by-Step Instructions

Follow these steps carefully

1

Lift and support the front of the car

Park on a flat surface, set the parking brake, and chock the rear wheels. Crack the front lug nuts loose, jack up the front, and set it on stands under the subframe rails. Shake the car to confirm it's stable.

2

Remove the wheel and inspect the brakes

Remove the front wheel to expose the disc brake assembly. Inspect the rotor for scoring, heat spots, or a raised lip, and check the pads through the caliper window. Photograph the hardware for reassembly.

3

Unbolt the caliper and hang it safely

Remove the two guide-pin bolts and wiggle the caliper off the rotor. Hang it from the strut coil spring with a bungee cord — never stretch or kink the hose. Pull the worn inner and outer pads from the bracket.

4

Service the caliper slide pins

Wire-brush the caliper bracket's pad abutment areas until they shine. Extract each slide pin, clean off old grease and corrosion, check the boots, and repack with fresh silicone brake grease — seized pins eat pads in a year.

🔧 Mechanic's note — Ray Delgado

Don't skip the slide pins on this car — the Intrepid eats pads when the pins seize, and it's the number-one cause of the 'my brakes only lasted a year' complaint I hear.

5

Retract the caliper piston

Remove the reservoir cap and check the fluid level. If the reservoir is already full, siphon some out with a turkey baster first. Then push the caliper piston squarely into its bore with a C-clamp, going slowly.

6

Fit the new pads and hardware clips

Install new or cleaned stainless clips with a whisper of brake grease on sliding contact points only. Seat the pads with the wear-squealer tab in the original inboard position — both should slide freely with finger pressure.

🔧 Mechanic's note — Ray Delgado

I put the wear-squealer tab on the inboard pad, same spot as the original — I've put one on the wrong pad before, and it squealed from day one.

7

Reassemble the caliper and wheel

Lower the caliper over the pads, hand-start the guide-pin bolts, and tighten evenly. Mount the wheel and snug the lugs in a star pattern; lower the car and final-torque them. Top the brake fluid to the full line if needed.

8

Seat the pads and verify the repair

Pump the brake pedal until high and firm; it must not sink with the engine running. Bed the pads with about five moderate 40-to-10-mph stops with cooling between, on an empty road. Re-torque lug nuts after 50 miles.

🔧 Mechanic's note — Ray Delgado

I re-torque the lugs after 50 miles — wheels settle on the hub and lugs back off, and I've skipped it before and earned a wobble that felt exactly like a warped rotor.

All Done!

Test your repair before closing everything up. If something doesn't work right, double-check your steps.

⚠️ Common Mistakes to Avoid

  • • Skipping the slide-pin service — on the 1998-2004 Intrepid the pins seize inside the bracket and drag one pad to metal while the other looks new.
  • • Prying the caliper off with a screwdriver against the rotor face — gouges the rotor and guarantees pedal pulsation; wiggle the caliper off by hand instead.
  • • Forgetting the reservoir cap — compressing the piston with the cap sealed can blow the reservoir seal or push fluid past the master cylinder seals.
  • • Reusing a torn caliper pin boot — water gets in, the pin rusts solid, and the new pads wear out in a few thousand miles.