← Back to Infiniti Q50 Guides

2014–2024 Infiniti Q50

2014-2024 Infiniti Q50 — Wiper Blade Replacement

By Tom Becker ✓ Certified Mechanic · Published Sep 21, 2026 · Updated Oct 22, 2026

🔧 Easy 10–15 minutes $66 DIY

Save $4 by doing it yourself! Shop cost: $70

Quick answer: Wiper Blade Replacement on a 2014–2024 Infiniti Q50 is rated Easy and takes about 10–15 minutes. You'll need 2 tools for this job, and parts cost about $66. This guide walks you through the full job step by step, including the mistakes to avoid.

Quick Video Tutorial

Parts You Need

Total Cost
$65.98
Part Name Part Number Price Buy
Driver wiper blade, 26" Bosch 26A $32.99
Passenger wiper blade, 17" Bosch 17B $32.99

About prices: shown prices are typical retail averages and change frequently; cheaper alternatives may be available. Confirm the current price before buying.

💡 Pro tip: Order all parts at once to save on shipping

Step-by-Step Instructions

Follow these steps carefully

1

Confirm the sizes and buy the blades

The 2014–2024 Infiniti Q50 takes a 26-inch blade on the driver side. The passenger side is 17 inches on most fitment charts, though a few list 16 inches — measure your old passenger blade with a tape before buying to be sure.

2

Park the wipers and lift the driver-side arm

Turn the Q50 off and confirm the wipers are parked at the base of the windshield. Do one side at a time so the 26-inch driver blade and the shorter passenger blade never get confused.

🔧 Mechanic's note — Tom Becker

Quick word from me — I've been under there: Do one side at a time so the 26-inch driver blade and the shorter passenger blade never get confused.

3

Release the old driver-side blade from the offset hook

The Q50 uses an offset hook-style arm. Lift the driver-side arm, then locate the release tab where the blade's adapter sits in the hook. Press the tab and slide the long 26-inch blade down out of the hook. Hold the bare arm with your other hand the whole time — it is under strong spring tension and will crack the glass if released.

4

Prep the new 26-inch blade

Pull the protective sleeve off the new blade without touching the rubber edge. Make sure the blade's adapter is configured for a hook arm — most aftermarket blades include a small adapter you snap into the hook position.

🔧 Mechanic's note — Tom Becker

In my experience, small thing, big difference: Make sure the blade's adapter is configured for a hook arm — most aftermarket blades include a small adapter you snap into the hook position.

5

Hook the new blade on and check the lock

Slide the new 26-inch blade into the arm's hook and pivot it up until the adapter clicks. Ease the arm back down onto the windshield, controlling it all the way.

6

Install the passenger blade

Repeat the tab-release and hook install for the passenger blade — 17 inches on most Q50s, 16 on some. Double-check: the 26-inch blade belongs on the driver side; a short blade on the wrong side leaves a large unwiped area.

7

Test with washer fluid

Start the car, spray washer fluid, and run the wipers through intermittent, low, and high speeds. The big 26-inch driver blade should clear its full arc without streaks or skips at the tip. If the passenger blade misses the outer edge of the glass, you may have bought a 16-inch blade for a 17-inch car — measure and swap before driving in rain.

All Done!

Test your repair before closing everything up. If something doesn't work right, double-check your steps.

⚠️ Common Mistakes to Avoid

  • • Buying two 26-inch blades — the Q50's passenger side is 17 inches or less
  • • Trusting a parts-store lookup without measuring, when charts split between 16-inch and 17-inch passenger blades
  • • Installing the hook adapter backward so the blade will not click in
  • • Letting the bare arm snap back onto the windshield while the blade is off