Quick answer: Ignition Coil Replacement on a 2019–2026 Volkswagen Jetta is rated Easy and takes about 30-45 minutes. You'll need 5 tools for this job, and parts cost about $109. This guide walks you through the full job step by step, including the mistakes to avoid.
Parts You Need
The options below are alternatives for the same part — you only need to buy one. Pick the one that matches your year and engine.
| Part Name |
Part Number |
Price |
Buy |
| Ignition Coil (2019-2021 1.4T) |
04E905110K |
$69.00 |
|
| Ignition Coil (2022-2026 1.5T) |
05E905110 |
$40.00 |
|
About prices: shown prices are typical retail averages and change frequently; cheaper alternatives may be available. Confirm the current price before buying.
💡 Pro tip: Compare the options above and order the one that matches your vehicle — you only need one.
Step-by-Step Instructions
Follow these steps carefully
1
Confirm the engine and the bad cylinder
This guide covers the non-GLI Jetta only: 2019-2021 with the 1.4L TSI (EA211, engine code DGXA) and 2022-2026 with the 1.5L TSI (EA211 evo, engine code DPCA). The GLI 2.0T (EA888) uses a different coil and is excluded. Read the codes with an OBD-II scanner: P0301, P0302, P0303 or P0304 names the misfiring cylinder, and P0300 means a random or multiple-cylinder misfire. To prove a coil is the culprit, swap the coil from the misfiring cylinder with a coil from a known-good cylinder, clear the codes, and drive briefly: if the misfire code follows the coil to the other cylinder, that coil is bad.
🔧 Mechanic's note — Ray Delgado
I always do the coil swap test before I order parts on these Jettas, because a misfire code alone will happily send you after the wrong cylinder and a new coil will not fix a bad plug or injector.
2
Park, cool down, and open the hood
Park on level ground, set the parking brake, and switch the ignition off. Let the engine cool completely if it was driven recently: the coils sit on top of the cylinder head and the surrounding parts stay hot long after shutdown.
3
Disconnect the negative battery terminal
Loosen the 10mm nut on the negative battery terminal and lift the cable off the post. Tuck it aside so it cannot spring back onto the terminal while you work.
4
Remove the engine cover
Pull the engine cover straight up off its rubber grommets to expose the four ignition coils on top of the valve cover. On the 1.4T, the air intake hose runs over the coils: loosen its clamp and move the hose aside if it blocks access.
5
Unplug the electrical connector
On the faulty coil, press the locking tab on the electrical connector and pull the connector straight off. Pull on the connector body, never on the wires. If you are replacing all four coils, unplug one at a time and keep each connector with its own cylinder: the coils themselves are interchangeable, but a connector must go back on the same cylinder it came from.
6
Remove the 10mm coil hold-down bolt
Remove the small 10mm bolt that secures the coil to the valve cover and set it aside where it cannot fall into the engine bay.
7
Pull the old coil straight up
Pull the coil off the spark plug, twisting if it resists. Use an ignition-coil puller if it will not budge: yanking at an angle can crack the coil or tear the boot. If the boot stays on the plug, fish it out with needle-nose pliers.
🔧 Mechanic's note — Ray Delgado
I keep a coil puller in the box for these because the boots bake onto the plug after a few summers, and the first time you yank one sideways you will be fishing rubber out of the well.
8
Check the part number before installing
Match the new coil to the engine: 2019-2021 1.4T takes OE 04E905110K (supersedes 04E905110B and 04E905110E); 2022-2026 1.5T takes OE 05E905110. The two coils look alike but are not interchangeable. Inspect the spark plug visible in the well: if it is fouled, worn, or oil-covered, replace it too, and find the cause of the oil before finishing.
9
Seat the new coil
Push the new coil firmly and squarely down onto the spark plug until it seats fully with no gap between the coil body and the valve cover. A coil that is not fully seated will misfire again immediately.
10
Reinstall the bolt and reconnect
Reinstall the 10mm hold-down bolt and tighten it snug by hand: no factory torque figure is published for this bolt, so do not overtighten it. Push the electrical connector back on until it clicks. Repeat steps 5-10 for any other coil you are replacing.
🔧 Mechanic's note — Ray Delgado
I tighten that little hold-down bolt by feel and stop the moment it snugs up, because the valve cover threads are soft and one hard pull with a ratchet will strip them.
11
Reinstall the cover and reconnect the battery
Refit the engine cover onto its grommets and reconnect the air intake hose if you moved it. Reconnect the negative battery terminal and tighten the 10mm nut.
12
Clear codes and test drive
Use the OBD-II scanner to clear the misfire codes, then start the engine and let it idle: it should run smooth with no flashing check engine light. Take a short test drive including light acceleration, then re-scan: no returning P0300-series code means the repair worked. If the misfire returns on the same cylinder after a confirmed-good coil, the fault is elsewhere (spark plug, injector, or compression) and needs further diagnosis.
All Done!
Test your repair before closing everything up. If something doesn't work right, double-check your steps.
⚠️ Common Mistakes to Avoid
- • Replacing all four coils without doing the coil-swap test first: usually only one coil has failed, and the other three can stay.
- • Ordering the wrong coil for the engine: the 1.4T coil (04E905110K) and the 1.5T coil (05E905110) look alike but are not interchangeable, and neither fits the GLI 2.0T.
- • Not pushing the new coil fully onto the spark plug: a partially seated coil misfires again immediately.
- • Mixing up the electrical connectors between cylinders after removing more than one coil at a time.
- • Overtightening the small 10mm hold-down bolt: it is a light fastener and the valve-cover threads strip easily.