EZCarFix DIY Auto Repair
← Back to Chevrolet Cruze Guides

2011–2015 Chevrolet Cruze

2011–2015 Chevrolet Cruze - Ignition Coil Replacement

By Tom Becker ✓ Certified Mechanic · Published Sep 21, 2026 · Updated Oct 22, 2026

🔧🔧 Moderate 1 hour $180 DIY 1 views

Save $220 by doing it yourself! Shop cost: $400

Quick answer: Ignition Coil Replacement on a 2011–2015 Chevrolet Cruze is rated Moderate and takes about 1 hour. You'll need 6 tools for this job, and parts cost about $180. This guide walks you through the full job step by step, including the mistakes to avoid.

Quick Video Tutorial

Parts You Need

The options below are alternatives for the same part — you only need to buy one. Pick the one that matches your year and engine.

Part Name Part Number Price Buy
Ignition coil rail/cassette, GM 55579072 / ACDelco D521C (1.4L turbo; one unit covers all 4 cylinders) 55579072 $148.61
Ignition coil rail/cassette, NGK 96739-07594103 (1.4L turbo) 96739-07594103 —
Ignition coil rail/cassette, Standard UF669 (1.4L turbo) UF669 $181.99
Coil cassette screws, ACDelco 11098802 (1.4L turbo; M6-1.0, 66mm long) 11098802 $6.99
Ignition coil, GM 55561655 / 25186687 / ACDelco 25186687 (1.8L; one per cylinder, 4 required) 55561655 —
Ignition coil, Delphi GN10234 (1.8L; one per cylinder, 4 required) GN10234 $133.99
Ignition coil, Standard UF620 (1.8L; one per cylinder, 4 required) UF620 $156.99
Spark plugs, ACDelco 41-121 (NGK IFR7X7G, stock 91039; 1.4L turbo; laser iridium, pre-gapped 0.027-0.028 in) 41-121 $13.49
Spark plugs, NGK IFR6Z7G, stock 95609 (1.8L; laser iridium, pre-gapped 0.027-0.028 in) IFR6Z7G $23.99

About prices: shown prices are typical retail averages and change frequently; cheaper alternatives may be available. Confirm the current price before buying.

💡 Pro tip: Compare the options above and order the one that matches your vehicle — you only need one.

Step-by-Step Instructions

Follow these steps carefully

1

Safety first: cold engine, battery disconnected

Work on a cold engine. Disconnect the negative battery cable before starting any electrical work. Wear gloves and safety glasses.

2

1.4L turbo: remove the engine cover

On the 1.4L turbo (LUJ for 2011-2012, LUV for 2013-2015), pull the plastic engine cover straight up. It has no fasteners; it is friction-fit on ball studs.

3

1.4L turbo: disconnect the cassette connector

Disconnect the single main electrical connector from the coil cassette. It uses a purple sliding lock tab: slide the lock back away from the cassette, then squeeze the release tab (marked with three grip lines) and wiggle the connector off.

4

1.4L turbo: remove the T-30 cassette screws

Remove the two Torx screws holding the cassette with a T-30 Torx bit. This size is confirmed by multiple sources; it is T-30, not T-40.

5

1.4L turbo: lift the cassette off

Pull the cassette straight up off the spark plugs, wiggling gently if it is stuck on the plug boots. Keep the cassette flat and level so the plug housings do not crack.

6

1.4L turbo: inspect the plug wells

While the cassette is off, inspect the spark plug wells for oil, coolant, or debris.

🔧 Mechanic's note — Tom Becker

I inspect the wells for oil before touching the plugs — oil in a well means a tube-seal leak, and I've seen new plugs fouled within days from ignoring it.

7

1.4L turbo: replace the spark plugs (optional)

If servicing the plugs, remove them with a 5/8-in (16mm) spark plug socket. Install ACDelco 41-121 (NGK IFR7X7G, stock 91039) laser-iridium plugs, pre-gapped at 0.027-0.028 in (0.7mm).

8

1.4L turbo: grease the cassette boots

Put a small amount of dielectric grease in each boot opening. It helps seal out moisture and makes the next removal easier.

9

1.4L turbo: install the new cassette

Press the new cassette straight down until each boot seats fully on its plug. Reinstall the two T-30 screws and snug them. No published torque spec exists for these screws, so do not overtighten.

10

1.4L turbo: reconnect and test

Reconnect the main electrical connector until it clicks and the purple lock tab is engaged. Reinstall the engine cover, reconnect the battery cable, start the engine, and confirm smooth running with no check-engine light or misfire codes (P0301-P0304).

🔧 Mechanic's note — Ray Delgado

I confirm the purple lock tab is engaged and check for misfire codes — I've had a connector back out from a missed lock tab, and the misfire was immediate.

11

1.8L: disconnect battery, remove engine cover

On the 1.8L naturally aspirated engine (LUW/LWE), disconnect the negative battery cable and remove the plastic engine cover to expose the four individual pencil coils. Quick visual check: a turbocharger plus one bar-shaped coil cassette means 1.4T; four separate pencil coils means 1.8L.

12

1.8L: disconnect the coil connectors

Release the locking tab on each coil's individual electrical connector and unplug it. One connector per coil.

13

1.8L: remove the coil hold-down bolts

Catalog data shows two mounting holes per coil on the Delphi design. Exact bolt head size was not confirmed in sources, so match a small metric socket to the bolt on your car.

14

1.8L: pull the coils

Pull each coil straight up out of its well, twisting gently if a boot is stuck to the plug.

15

1.8L: inspect the plug wells

Inspect each spark plug well for oil, coolant, or debris before proceeding. Oil in a well means a valve-cover tube-seal leak that must be fixed first.

🔧 Mechanic's note — Tom Becker

I look for oil in the wells on the 1.8L too — a tube-seal leak fouls new plugs fast, and I've learned to fix the seal first.

16

1.8L: replace the spark plugs (optional)

If servicing the plugs, remove them with a 5/8-in (16mm) spark plug socket. Install NGK IFR6Z7G (stock 95609) laser-iridium plugs, pre-gapped at 0.027-0.028 in (0.7mm). No anti-seize.

17

1.8L: grease the coil boots

Apply a small amount of dielectric grease to the opening of each coil's rubber dust boot. It keeps moisture out and ensures a reliable connection.

18

1.8L: install the new coils

Start the hold-down bolt or bolts by hand to avoid cross-threading, then tighten snug. No verified torque spec is published for these bolts, so do not overtighten.

19

1.8L: reconnect and test

Push each electrical connector straight in until it clicks. Reinstall the engine cover, reconnect the battery cable, start the engine, and verify a smooth idle with no misfire codes.

All Done!

Test your repair before closing everything up. If something doesn't work right, double-check your steps.

⚠️ Common Mistakes to Avoid

  • • Not disconnecting the battery before starting the repair
  • • Forcing the ignition coil out, which can damage the coil or surrounding components
  • • Failing to apply dielectric grease to the new ignition coil, leading to poor electrical contact