Quick answer: Wiper Blade Replacement on a 2010–2017 Volvo XC60 is rated Easy and takes about 15–20 minutes. Parts cost about $81. This guide walks you through the full job step by step, including the mistakes to avoid.
| Part Name |
Part Number |
Price |
Buy |
| Driver wiper blade, 26" |
Bosch 26A |
$32.99 |
|
| Passenger wiper blade, 20" |
Bosch 20B |
$32.99 |
|
| Rear wiper blade, 14" |
— |
$14.99 |
|
About prices: shown prices are typical retail averages and change frequently; cheaper alternatives may be available. Confirm the current price before buying.
💡 Pro tip: Order all parts at once to save on shipping
Step-by-Step Instructions
Follow these steps carefully
1
Confirm the sizes and buy the blades
26-inch driver, 20-inch passenger — buy one of each. Rear is 14 inches on 2013–2017; 2010–2012 charts list 15, so measure the old rear. Front arms use a 19mm top-button connector — buy Volvo top-button blades, not generic J-hook.
🔧 Mechanic's note — Ray Delgado
Double-check the rear blade with a tape measure before you buy — I've seen 2010–2012 XC60s with a 15-inch rear and charts that swear it's 14. Five seconds with a tape measure beats a second trip.
2
Park and prep — no service position needed
Wipers park on the glass — no service position, just lift the arms. Ignition off, wiper stalk off. Work one side at a time so the 26-inch and 20-inch blades never get mixed up.
3
Release the old driver-side blade
Lift the driver-side arm up. Find the release button or locking tab on the center connector and press it while sliding the blade down off the pin. Hold the bare arm — it can snap back and crack the windshield.
🔧 Mechanic's note — Ray Delgado
That top-button clip has to click — I've seen blades fly off at highway speed because someone pushed one on without seating the clip. Tug it hard before you call it done.
4
Prep the new 26-inch blade
Remove the protective sleeve; don't touch the rubber wiping edge. Confirm the 19mm top-button adapter is already fitted — the clip must click over the arm's button. Hold old and new side by side to confirm the 26-inch length matches.
5
Slide the new blade on and check the lock
Slide the new 26-inch blade onto the arm's pin until the clip clicks. Tug it firmly along the arm — no sliding, rocking, or rattling. If it moves, reseat it until the click is unmistakable. Lower the arm gently onto the glass.
6
Do the passenger side and the rear blade
Repeat for the 20-inch passenger blade. Press the tab and slide the old blade off its snap-claw or U-clip (2016–2017 snap-claw, earlier U-clip), then snap the new 14-inch (or 15-inch) on. Support the rear arm so it can't snap back onto the glass.
7
Test with washer fluid
Start the car and spray the washers on all wiper speeds. Each blade sweeps clean — no streaks, skips, or chattering. Run the rear washer and wiper; the rear blade should clear its arc. Re-seat any chattering blade — its clip didn't fully engage.
All Done!
Test your repair before closing everything up. If something doesn't work right, double-check your steps.
⚠️ Common Mistakes to Avoid
- • Buying two 26-inch blades — the XC60 passenger side is 20 inches
- • Buying generic J-hook blades that will not fit the Volvo 19mm top-button arm
- • Assuming the rear blade size instead of measuring — 2010–2012 charts disagree between 14 and 15 inches
- • Letting the bare arm snap back onto the windshield while the blade is off
