EZCarFix DIY Auto Repair
← Back to Chevrolet Cruze Guides

2011–2015 Chevrolet Cruze

2011-2015 Chevrolet Cruze — Wiper Blade Replacement

By Ray Delgado ✓ Certified Mechanic · Published Sep 21, 2026 · Updated Oct 22, 2026

🔧 Easy 10–15 minutes $66 DIY

Quick answer: Wiper Blade Replacement on a 2011–2015 Chevrolet Cruze is rated Easy and takes about 10–15 minutes. You'll need 2 tools for this job, and parts cost about $66. This guide walks you through the full job step by step, including the mistakes to avoid.

Quick Video Tutorial

Parts You Need

Total Cost
$65.98
Part Name Part Number Price Buy
Driver wiper blade, 24" Bosch 24A $32.99
Passenger wiper blade, 18" Bosch 18B $32.99

About prices: shown prices are typical retail averages and change frequently; cheaper alternatives may be available. Confirm the current price before buying.

💡 Pro tip: Order all parts at once to save on shipping

Step-by-Step Instructions

Follow these steps carefully

1

Confirm the fitment: 24-inch driver, 18-inch passenger — first generation only

First-gen Cruze: 24-inch driver, 18-inch passenger, J-hook arms (9×3 mm). No rear wiper on the sedan. Second-gen (2016+, except the 2016 Limited carryover) switched to 28/24-inch blades on different arms — confirm listings cover 2011–2015.

2

Park, power off, and set up

Park level, ignition off, wiper stalk OFF. No service position — the arms park on the glass and lift straight up, clearing the hood. Lay a folded towel under the arm; a snapping bare arm can crack the windshield.

3

Remove the driver-side blade from the J-hook

Lift the arm, press the release tab, and slide the blade down off the J-hook. If the tab is gummed, wipe the connector clean rather than forcing it — the Cruze's cowl collects debris. Compare old and new 24-inch blades.

4

Install the new 24-inch driver blade

Slide the new blade up the J-hook until the tab clicks, then tug firmly to confirm it's locked. Lower the arm gently. The driver's-side glass curves — sight along the blade to confirm no lifted ends, or it will chatter.

5

Repeat on the 18-inch passenger blade

Repeat on the passenger side with the 18-inch blade: press tab, slide off, slide on until it clicks, tug-test, lower gently. Don't mix sides — an 18-inch blade on the driver's side leaves an unwiped arc in line of sight.

6

Inspect the cowl and washer nozzles

Clear leaves from the cowl panel by hand. Run the washers and confirm both nozzles spray evenly; clear clogs with a pin and top up the fluid. A clogged nozzle is the cause of most "new blades still streak" complaints.

🔧 Mechanic's note — Ray Delgado

Before you blame a new blade for streaking, run the washers and watch both nozzles. On first-gen Cruzes I see clogged hood nozzles more often than bad blades — a pin and thirty seconds fixes what a second set of blades won't.

7

Test the wipers

Turn the ignition on, spray the washers, and cycle the wipers at both speeds, checking for streaks, skipped bands, or chatter. A chattering blade is installed backwards or not seated — recheck the connector first. Confirm arms park flat.

All Done!

Test your repair before closing everything up. If something doesn't work right, double-check your steps.

⚠️ Common Mistakes to Avoid

  • • Buying 28/24-inch blades listed for the 2016+ second-generation Cruze — the 2011–2015 car takes 24/18.
  • • Installing the 18-inch blade on the driver’s side, leaving an unwiped arc in the driver’s sightline.
  • • Forcing a grime-seized release tab instead of wiping the connector clean first.
  • • Ignoring the debris-packed cowl, which then ruins the new blades’ performance.