← Back to Chrysler Sebring Guides

2001–2006 Chrysler Sebring

2001-2006 Chrysler Sebring — 12V Battery Replacement

By Ray Delgado ✓ Certified Mechanic · Published Sep 21, 2026 · Updated Oct 22, 2026

🔧 Easy 30-90 minutes $180 DIY

Save $120 by doing it yourself! Shop cost: $300

Quick answer: 12V Battery Replacement on a 2001–2006 Chrysler Sebring is rated Easy and takes about 30-90 minutes. You'll need 2 tools for this job, and parts cost about $180. This guide walks you through the full job step by step, including the mistakes to avoid.

Quick Video Tutorial

Parts You Need

Total Cost
$180.00
Part Name Part Number Price Buy
Replacement 12-volt battery for 2001-2006 Chrysler Sebring; verify group size, CCA, terminal layout, and VIN fitment — $180.00
Anti-corrosion terminal protectant or felt washers (optional) Optional — $8.00

About prices: shown prices are typical retail averages and change frequently; cheaper alternatives may be available. Confirm the current price before buying.

💡 Pro tip: Order all parts at once to save on shipping

Step-by-Step Instructions

Follow these steps carefully

1

Confirm the right battery and the real symptom

Battery group varies: sedans commonly use Group 75 or Group 26, while the coupe commonly uses Group 86, so read the group code on your old battery before buying. Confirm the failure first: slow cranking or repeated no-starts point to the battery.

2

Shut the car down and set up for wheel-well access

Chock the rear wheels, then loosen the driver-side front lug nuts slightly before raising that corner with a jack and securing it on a jack stand — never work under a car supported only by a jack.

3

Open the wheel well to reach the battery

Turn the steering wheel fully to the right to open working room, or remove the driver-side front wheel entirely for the easiest access. Some Sebrings have a heat pad wrapped around the battery — note how it sits so you can refit it.

4

Disconnect the old battery, negative first

Working through the wheel well, loosen the negative clamp first and pull it off the post, tucking the cable where it cannot spring back. Slide the old battery out through the wheel-well opening, supporting its weight as it comes free.

5

Set the new battery in and reconnect

Slide the new battery into the wheel-well compartment in the original orientation, matching the old battery's group size and terminal layout exactly. Refit the top hold-down clamp and tighten its bolts snugly. Connect the positive cable first and tighten it, then the negative.

6

Close up the wheel well

Reposition the splash shield and reinstall all its clips and screws — a loose shield will flap, rub the tire, and let road spray soak the battery. Refit the wheel if removed and torque the lug nuts to spec with the car on the ground.

7

Verify charging and recycle the old battery

With the engine running you should see 13.5 to 14.5 volts at the underhood jump-start posts and no battery warning light. Confirm the headlights and accessories behave. Return the old battery to the parts store for its core refund and proper recycling.

🔧 Mechanic's note — Tom Becker

Battery jobs have bitten me before: Don't forget the heat pad — it wraps around the battery for a reason, and the wheel-well heat will shorten the new battery's life if you leave it off.

All Done!

Test your repair before closing everything up. If something doesn't work right, double-check your steps.

⚠️ Common Mistakes to Avoid

  • • Buying by appearance instead of group size, CCA, polarity, and hold-down fit
  • • Shorting the positive terminal to the body with a metal tool
  • • Lifting the battery by damaged terminals or leaving it unsecured
  • • Skipping battery registration, window/clock resets, or charging-system checks when required
  • • Assuming a new battery fixes a parasitic draw or charging fault