EZCarFix DIY Auto Repair
← Back to Fiat 500L Guides

2014–2020 Fiat 500L

2014-2020 Fiat 500L — Wiper Blade Replacement

By Ray Delgado ✓ Certified Mechanic · Published Sep 21, 2026 · Updated Oct 22, 2026

🔧 Easy 15–20 minutes for front pair plus rear blade $81 DIY

Quick answer: Wiper Blade Replacement on a 2014–2020 Fiat 500L is rated Easy and takes about 15–20 minutes for front pair plus rear blade. You'll need 1 tool for this job, and parts cost about $81. This guide walks you through the full job step by step, including the mistakes to avoid.

Quick Video Tutorial

Parts You Need

Total Cost
$80.97
Part Name Part Number Price Buy
Driver wiper blade, 26" Bosch 26A $32.99
Passenger wiper blade, 15" Bosch 15B $32.99
Rear wiper blade, 12" — $14.99

About prices: shown prices are typical retail averages and change frequently; cheaper alternatives may be available. Confirm the current price before buying.

💡 Pro tip: Order all parts at once to save on shipping

Step-by-Step Instructions

Follow these steps carefully

1

Confirm the correct blade sizes for your 500L

Asymmetric set: 26-inch driver, 15-inch passenger, 12-inch rear. Front arms are push-button (top-lock, 19mm) — not J-hook — so buy push-button blades; verify the adapter is included. Aftermarket coverage is thin (discontinued in NA after 2020): measure old blades tip-to-tip and match the rear connector.

2

Park the car and lift the front wiper arms

Park level, brake set, ignition fully off. Wipers park clear of the hood — no service position; pull each front arm straight up. Frozen blades: defrost fully first — tearing one loose damages rubber and strains the linkage. One side at a time.

🔧 Mechanic's note — Ray Delgado

A bare wiper arm snapping onto the glass is a cracked-windshield invoice — I've seen it happen reaching for a dropped clip. The folded towel takes two seconds and has saved more windshields than I can count.

3

Remove the old driver-side blade from the push-button connector

Find the push button on the top-lock clip. Press it; slide the blade down toward the pivot about an inch, lift off. Slide straight — never twist; twisting cracks the plastic. Don't let the bare arm snap down — it cracks the windshield.

4

Install the new 26-inch driver-side blade

Seat the push-button adapter in the center clip — universals include several; only the push-button one fits. Align with the mounting pin; slide up away from the pivot until the button snaps. Tug-test firmly both ways; lower the arm gently.

🔧 Mechanic's note — Ray Delgado

That tug test is the whole job for me — a blade on the wrong adapter feels fine until 60 mph, when it departs the car. I pull it hard both ways; if it moves at all, I've got the wrong adapter.

5

Replace the 15-inch passenger-side blade

Passenger side: press the button, slide the old blade down off the pin. Confirm length against the new 15-inch blade; the asymmetry is correct. Install until the button clicks, tug-test, fold the arm back. Confirm the blades don't collide mid-sweep.

6

Replace the 12-inch rear wiper blade

Lift the short arm — don't force it. The blade releases via a small center clip or slide; rear connectors vary by supplier, so match the old one. Install the 12-inch blade until it locks; confirm it pivots. Wrong connector? Return it.

7

Test front and rear wipers, then clean up

Ignition on; wet the glass with the washer — never dry-run new blades. Cycle intermittent and both speeds: no chatter, skipping, or contact. Run the rear wiper and washer; confirm a clean arc. Keep the packaging until proven in rain.

All Done!

Test your repair before closing everything up. If something doesn't work right, double-check your steps.

⚠️ Common Mistakes to Avoid

  • • Buying J-hook blades by habit — the 500L's front arms use a push-button top-lock connector, and a hook-style blade cannot be made to fit safely.
  • • Swapping the asymmetric lengths — the 26-inch blade must go on the driver side and the 15-inch on the passenger side; reversing them leaves an unwiped zone and can cause blade collision.
  • • Twisting a seized top-lock connector instead of pressing and sliding straight — the plastic clip can crack; press the button firmly and slide in line with the arm.
  • • Improvising a mismatched rear blade connector — 500L rear fittings vary by supplier, so an incorrect rear blade must be exchanged, not forced on.