EZCarFix DIY Auto Repair
← Back to Chevrolet Blazer Guides

2019–2024 Chevrolet Blazer

2019-2024 Chevrolet Blazer — Spark Plug Replacement

By Tom Becker ✓ Certified Mechanic · Published Sep 21, 2026 · Updated Oct 22, 2026

🔧🔧🔧 Advanced 1-3 hours $115 DIY

Save $335 by doing it yourself! Shop cost: $450

Quick answer: Spark Plug Replacement on a 2019–2024 Chevrolet Blazer is rated Advanced and takes about 1-3 hours. You'll need 4 tools for this job, and parts cost about $115. This guide walks you through the full job step by step, including the mistakes to avoid.

Quick Video Tutorial

Parts You Need

Total Cost
$115.00
Part Name Part Number Price Buy
Correct spark plug set for 2019-2024 Chevrolet Blazer; verify engine, heat range, gap, and VIN fitment — $115.00
Coil-boot seals or ignition coils only if inspection finds damage Optional — $35.00

About prices: shown prices are typical retail averages and change frequently; cheaper alternatives may be available. Confirm the current price before buying.

💡 Pro tip: Order all parts at once to save on shipping

Step-by-Step Instructions

Follow these steps carefully

1

Confirm engine and plug fitment

This guide covers the 2019-2024 Chevrolet Blazer. Two engines were offered: the 2.5L LCV four-cylinder uses NGK LTR5IX-11 (stock 4344) iridium plugs gapped to 0.044 in, and the 3.6L LGX V6 uses ACDelco GM OE iridium plugs that come pre-gapped from the factory — do not attempt to re-gap them. Buy four plugs for the 2.5L or six for the 3.6L. Confirm your engine on the underhood emissions sticker before ordering, then scan for misfire codes (P0300-P0306). Check the underhood emissions sticker to confirm whether you have the 2.5L or the 3.6L before buying plugs — the parts are not interchangeable.

2

Cool and expose the plugs

Let the engine cool completely. Remove the plastic engine cover to expose the coil-on-plug units on top of the valve cover — both Blazer engines have straightforward top access with no intake removal needed. Disconnect the negative battery cable as a safety step before unplugging coils. Label each coil connector so every coil returns to its own cylinder.

3

Remove coils and clean wells

Unplug each coil connector by releasing the locking tab, remove the hold-down bolt, and pull each coil straight up out of its tube. Blow compressed air down every plug well before loosening a plug; grit falling into the cylinders can score the walls. Inspect each coil boot for cracks, brittleness, or carbon tracking — a damaged boot will keep misfiring even with a new plug installed.

🔧 Mechanic's note — Tom Becker

Shop habit of mine: Inspect each coil boot for cracks, brittleness, or carbon tracking — a damaged boot will keep misfiring even with a new plug installed.

4

Remove and install plugs

Use a 5/8 in spark plug socket. Crack each old plug loose and spin it out by hand. On the 2.5L, verify the NGK LTR5IX-11 gap at 0.044 in with a wire gauge; on the 3.6L, install the ACDelco plugs exactly as they come out of the box. Thread each new plug in by hand to protect the aluminum head threads, then tighten to the factory torque spec with a torque wrench. Never use an impact, and do not use anti-seize on the coated threads. Both Blazer engines offer straightforward top access with no intake removal, so a basic 5/8 in socket and ratchet handle the whole job.

🔧 Mechanic's note — Ray Delgado

I've learned: this is the part people get wrong: Never use an impact, and do not use anti-seize on the coated threads.

5

Reconnect and verify

Reinstall the coils, tighten the hold-down bolts, and click each connector back on until the tab locks. Reconnect the battery and start the Blazer. Let it idle and watch for a flashing check-engine light, which means an active misfire.

All Done!

Test your repair before closing everything up. If something doesn't work right, double-check your steps.

⚠️ Common Mistakes to Avoid

  • • Using the wrong plug or assuming a pre-gapped plug needs no verification
  • • Blowing debris into an open cylinder or plug well
  • • Cross-threading a plug or tightening it without a torque wrench
  • • Overusing anti-seize or dielectric grease on the plug threads
  • • Mixing coil connectors or ignoring a misfire after reassembly