EZCarFix DIY Auto Repair
← Back to Chevrolet Blazer Guides

2019–2024 Chevrolet Blazer

2019-2024 Chevrolet Blazer — Wiper Blade Replacement

By Ray Delgado ✓ Certified Mechanic · Published Sep 21, 2026 · Updated Oct 22, 2026

🔧 Easy 10–15 minutes $81 DIY

Quick answer: Wiper Blade Replacement on a 2019–2024 Chevrolet Blazer is rated Easy and takes about 10–15 minutes. You'll need 1 tool for this job, and parts cost about $81. This guide walks you through the full job step by step, including the mistakes to avoid.

Quick Video Tutorial

Parts You Need

Total Cost
$80.97
Part Name Part Number Price Buy
Driver wiper blade, 24" Bosch 24A $32.99
Passenger wiper blade, 18" Bosch 18B $32.99
Rear wiper blade, 12" — $14.99

About prices: shown prices are typical retail averages and change frequently; cheaper alternatives may be available. Confirm the current price before buying.

💡 Pro tip: Order all parts at once to save on shipping

Step-by-Step Instructions

Follow these steps carefully

1

Confirm the fitment: 24-inch driver, 18-inch passenger, 12-inch rear

The 2019–2024 Blazer crossover takes 24 driver, 18 passenger, 12 rear — J-hooks (9×3 mm); the rear is a framed blade with a shroud on a 9×3 hook. Some catalogs say 11 — GM says 12; measure rear blade first.

🔧 Mechanic's note — Ray Delgado

In my experience, Don't let a catalog talk you out of the 12-inch rear blade — GM lists 12 inches, and the 11-inch listings are just wrong. Measure your old one, but if it reads 11, someone before you bought the wrong size.

2

Park, power off, and set up

Park level, ignition off, wiper stalk OFF. No service position — arms park on the glass and lift up. Lay a towel under the arm; a snapping arm can crack the windshield — raked glass puts the impact in sightline.

3

Remove the driver-side blade from the J-hook

Lift the arm clear, press the release tab, and slide the blade down off the J-hook — keep it parallel, don't twist. Lay the new blade beside the old one to confirm 24 inches.

4

Install the new 24-inch driver-side blade

Feed the J-hook through connector and slide it up until the tab clicks. Tug — a loose 24-inch blade can detach at highway speed. Lower gently. Sight along the blade — no lifted corners, or it will skip and chatter.

5

Repeat on the 18-inch passenger blade

Repeat on the passenger side: press tab, slide off, slide the 18-inch blade on until it clicks, lower. Don't mix sides — 18-inch blade on driver's side leaves a gap. Flex hinge — binding one causes streaking blades can't fix.

6

Swap the 12-inch rear blade

Lift rear arm off the glass. Press tab; slide the blade off the 9×3 hook, then slide the 12-inch blade on until it clicks. If your old blade was 11 inches, match the 12-inch spec unless it overruns the glass.

7

Test all three wipers

Ignition on: spray fluid and run the fronts at both speeds, checking for streaks or chatter. Run the rear wiper and washer — nozzle clogs with wax. Confirm all three arms park flat. Replace all three about once a year.

All Done!

Test your repair before closing everything up. If something doesn't work right, double-check your steps.

⚠️ Common Mistakes to Avoid

  • • Ordering an 11-inch rear blade from a catalog that undersizes it — the spec is 12 inches; measure the old blade.
  • • Putting the 18-inch blade on the driver’s side, leaving an unwiped band in the driver’s sightline.
  • • Confusing this Blazer with the old S-10-based Blazer or the Blazer EV when ordering.
  • • Skipping the tug-test on the long 24-inch driver blade.